1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 3
  1. Jake Ciasca
    Post

    Unresolved PETG warping issue

    Awesome, I will check netfabb out right now, I wish I had simplify 3d but since it costs so much money I really don't want to spend money when...
    Post by: Jake Ciasca, Feb 12, 2021 in forum: Troubleshooting
  2. Jake Ciasca
    Post

    Unresolved PETG warping issue

    But that's the thing, the warpage only happened on one side of the print and it didn't happen to the raft, so is it still the same cause? And is...
    Post by: Jake Ciasca, Feb 12, 2021 in forum: Troubleshooting
  3. Jake Ciasca
    Post

    Unresolved PETG warping issue

    Well, how would a better toolpath basically eliminate the warpage from the petg like what happened in the first picture from this post?
    Post by: Jake Ciasca, Feb 12, 2021 in forum: Troubleshooting
  4. Jake Ciasca
    Post

    Unresolved PETG warping issue

    I’m using an older version of cura because I download the newest version of cura and there was a lot of new settings that I didn’t want to mess...
    Post by: Jake Ciasca, Feb 12, 2021 in forum: Troubleshooting
  5. Jake Ciasca
    Post

    Unresolved PETG warping issue

    That's the thing, I have printed another cooling fan duct for the original robo r1 fan, and on top of that, I printed another one for a second fan...
    Post by: Jake Ciasca, Feb 9, 2021 in forum: Troubleshooting
  6. Jake Ciasca
    Thread

    Unresolved PETG warping issue

    So I recently got a batch of hatchbox petg and I adjusted some of my print settings like temperature both bed and nozzle and basic stuff that...
    Thread by: Jake Ciasca, Feb 8, 2021, 14 replies, in forum: Troubleshooting
  7. Jake Ciasca
    Post

    Solved Bed tries to move farther than it can

    Oh I fixed the problem, it was the heated bed ribbon cable that was sticking out a tad bit on the bottom and was a slight amount so it couldn't...
    Post by: Jake Ciasca, Jul 8, 2020 in forum: Troubleshooting
  8. Jake Ciasca
    Post

    Solved Bed tries to move farther than it can

    Okay so it doesn't look like the bed/belt is skipping so what could this possibly be then, could it be the y-steps are not calibrated or something...
    Post by: Jake Ciasca, Jul 8, 2020 in forum: Troubleshooting
  9. Jake Ciasca
    Post

    Solved Error in Arduino

    Installing that library seemed to work, since this is a fresh download onto a new desktop that's why I probably didn't have it.
    Post by: Jake Ciasca, Jul 4, 2020 in forum: Troubleshooting
  10. Jake Ciasca
    Post

    Solved Error in Arduino

    Could you link the thread to where I could get the newer arduino software and make it work with the r1 firmware because when I got my lcd screen...
    Post by: Jake Ciasca, Jul 4, 2020 in forum: Troubleshooting
  11. Jake Ciasca
    Post

    Solved Error in Arduino

    How would I add that to the project?
    Post by: Jake Ciasca, Jul 4, 2020 in forum: Troubleshooting
  12. Jake Ciasca
    Post

    Solved Bed tries to move farther than it can

    Could it be that in the firmware Could it be that in the firmware I might've set what the actual bed length is longer than the bed itself and it...
    Post by: Jake Ciasca, Jul 4, 2020 in forum: Troubleshooting
  13. Jake Ciasca
    Thread

    Solved Error in Arduino

    I'm getting an error in arduino trying to compile the firmware to the board and I have no idea what it means or how to fix it, does anybody know?...
    Thread by: Jake Ciasca, Jul 4, 2020, 7 replies, in forum: Troubleshooting
  14. Jake Ciasca
    Post

    Unresolved Weird Layer Discrepancies

    How do you season the hotend, I couldn't seem to find anything in the previous link about how to season the hotend.
    Post by: Jake Ciasca, Jul 4, 2020 in forum: Troubleshooting
  15. Jake Ciasca
    Post

    Unresolved Weird Layer Discrepancies

    Yes this is PLA and I have not tried seasoning the nozzle and I have no idea what that means so I will check the link you sent me and see if that...
    Post by: Jake Ciasca, Jul 4, 2020 in forum: Troubleshooting
  16. Jake Ciasca
    Thread

    Unresolved Weird Layer Discrepancies

    I messed around with the flow in the slicer i used changing it from 95% to 100% to 105% and finally 110% thinking this was an under extrusion...
    Thread by: Jake Ciasca, Jul 3, 2020, 6 replies, in forum: Troubleshooting
  17. Jake Ciasca
    Thread

    Solved Bed tries to move farther than it can

    The bed of my printer seems to be trying to move farther than it can move and I'm not sure if I have to change the g-code or settings in the...
    Thread by: Jake Ciasca, Jul 3, 2020, 6 replies, in forum: Troubleshooting
  18. Jake Ciasca
    Thread

    Answered Temp Fall Error Fix?

    This issue has been happening more and more and I'm not sure why, I recently installed an E3D V6 hotend and it was working for a little bit and...
    Thread by: Jake Ciasca, Feb 1, 2020, 1 replies, in forum: Troubleshooting
  19. Jake Ciasca
    Post

    Solved Extruder Calibration and Esteps

    Ok still a little confused but I was able to use the gcode and it changed the firmware so that is good. Thank you!
    Post by: Jake Ciasca, Jul 3, 2019 in forum: Troubleshooting
  20. Jake Ciasca
    Post

    Solved Extruder Calibration and Esteps

    Do you have to use the EEPROM? And if so when would I have enabled it and how?
    Post by: Jake Ciasca, Jul 3, 2019 in forum: Troubleshooting
Showing results 1 to 20 of 44 Next >
Search Again
Page 1 of 3