1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. KADOW
    Post

    Answered Prints ending mid or early

    Thank you i will try that tomorrow and get into the startup for the printer amd see how it goes also what do you use to season your nozzle ?
    Post by: KADOW, Aug 15, 2018 in forum: Troubleshooting
  2. KADOW
    Post

    Answered Prints ending mid or early

    Ok i will keep trying the seasoning any sugestions on oils and why would it print at all with or with out seasoning ? Also you mentioned g code...
    Post by: KADOW, Aug 15, 2018 in forum: Troubleshooting
  3. KADOW
    Post

    Answered Prints ending mid or early

    Yes i had an oiler printed by a friend because i can not even print that out. I also have made sure it is extruding the correct length of...
    Post by: KADOW, Aug 15, 2018 in forum: Troubleshooting
  4. KADOW
    Thread

    Answered Prints ending mid or early

    So i have an E3d installed from printed solid I have printes calibration cubes and they come out pretty good but thats is all i can print. When...
    Thread by: KADOW, Aug 15, 2018, 8 replies, in forum: Troubleshooting
  5. KADOW
    Post

    Solved Is this Layer height

    Sorry yea this ia Blue PLA from BAMtack yes I printed it at 200, 205, 210, then 220. All with similar results I will check the micro clog post.
    Post by: KADOW, Jun 25, 2018 in forum: Troubleshooting
  6. KADOW
    Post

    Solved Is this Layer height

    So i downloaded the file and now this is what I am getting at any temp. It stops printing and then starts to eat through the filament.
    Post by: KADOW, Jun 25, 2018 in forum: Troubleshooting
  7. KADOW
    Post

    Solved Is this Layer height

    I don't suppose anyone has a temp tower already set up for matter control I looked at them on thingiverse and most do not have auto bed leveling I...
    Post by: KADOW, Jun 25, 2018 in forum: Troubleshooting
  8. KADOW
    Thread

    Solved Is this Layer height

    So finally got my endstop issue fixed but I have some what i think are layer height issues. Created a calibration cube and then some parts and the...
    Thread by: KADOW, Jun 25, 2018, 8 replies, in forum: Troubleshooting
  9. KADOW
    Post

    Answered X axis ?

    OK so then what would be my next step could the board be the issue? Any suggestions as maybe what to trouble shoot next.
    Post by: KADOW, Mar 1, 2018 in forum: Troubleshooting
  10. KADOW
    Post

    Answered X axis ?

    So i got my new switch today and still not working correctly now goes far right and does nothing. [MEDIA]
    Post by: KADOW, Mar 1, 2018 in forum: Troubleshooting
  11. KADOW
    Post

    Answered X axis ?

    Yes it is wired wrong but that is the only way it will auto home if I wire it correctly the carriage goes to the right and then stops completely...
    Post by: KADOW, Feb 27, 2018 in forum: Troubleshooting
  12. KADOW
    Post

    Answered X axis ?

    So here is another video I also noticed that in the picture above the switch is connected to the outside poles mine only auto homes on the front...
    Post by: KADOW, Feb 27, 2018 in forum: Troubleshooting
  13. KADOW
    Thread

    Answered X axis ?

    So I installed the E3d V6 everything is working except when I put my printer back together this is what's happening I have check my wires and...
    Thread by: KADOW, Feb 27, 2018, 11 replies, in forum: Troubleshooting
Showing results 1 to 13 of 13
Search Again