1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Nicholai Lekson
    Post

    Solved R1+ RAMPS board zero voltage across Fans / LED

    I replaced the Mega with a new one, and the issues went away! In fact, I got everything working shortly after, and now my R1+ is printing quieter,...
    Post by: Nicholai Lekson, Jul 5, 2018 in forum: Troubleshooting
  2. Nicholai Lekson
    Post

    Solved R1+ RAMPS board zero voltage across Fans / LED

    I've read that thread multiple times, and to me it contains no pertinent information. I believe the cause of such erratic measurements is from a...
    Post by: Nicholai Lekson, Jul 4, 2018 in forum: Troubleshooting
  3. Nicholai Lekson
    Post

    Solved R1+ RAMPS board zero voltage across Fans / LED

    I found out the issue was with wiring on the cable I bought, the phases weren't properly wired at the RAMPS plug, so I fixed that and it works...
    Post by: Nicholai Lekson, Jul 4, 2018 in forum: Troubleshooting
  4. Nicholai Lekson
    Post

    Solved R1+ RAMPS board zero voltage across Fans / LED

    I decided to go the generic RAMPS route, but it seems that my extruder stepper refuses to work! I have swapped the motor to the X stepper wires,...
    Post by: Nicholai Lekson, Jul 3, 2018 in forum: Troubleshooting
  5. Nicholai Lekson
    Thread

    Solved R1+ RAMPS board zero voltage across Fans / LED

    Hello all, Now that I have replaced my stepper motor cable, another issue has arisen regarding the RAMPS board. After testing everything, the LED,...
    Thread by: Nicholai Lekson, Jul 1, 2018, 19 replies, in forum: Troubleshooting
  6. Nicholai Lekson
    Post

    Answered Extruder Stalls and clicks in certain Y location consistently

    @Geof Your idea was correct! Jostling the 4 wire leads on the Stepper caused the horrible grinding sound. That solved the issue pretty simply, I...
    Post by: Nicholai Lekson, Jun 29, 2018 in forum: Troubleshooting
  7. Nicholai Lekson
    Post

    Answered Extruder Stalls and clicks in certain Y location consistently

    Sounds like a good idea. I will try that as soon as I get home from work.
    Post by: Nicholai Lekson, Jun 28, 2018 in forum: Troubleshooting
  8. Nicholai Lekson
    Post

    Answered Extruder Stalls and clicks in certain Y location consistently

    In addition, upon feeling the motor torque during these "hang-ups" where it clicks, it feels as though it suddenly loses all of its toque In that...
    Post by: Nicholai Lekson, Jun 26, 2018 in forum: Troubleshooting
  9. Nicholai Lekson
    Post

    Answered Extruder Stalls and clicks in certain Y location consistently

    It is trying to extrude, because even turning off Retraction in Simplify3D does absolutely nothing to remedy the issue. Could it be the stepper...
    Post by: Nicholai Lekson, Jun 26, 2018 in forum: Troubleshooting
  10. Nicholai Lekson
    Post

    Answered Extruder Stalls and clicks in certain Y location consistently

    Even with the extruder lifted from the bed it stalls in that position, which is why I find it especially confusing. Even after switching to Cura,...
    Post by: Nicholai Lekson, Jun 25, 2018 in forum: Troubleshooting
  11. Nicholai Lekson
    Post

    Answered Extruder Stalls and clicks in certain Y location consistently

    This is the R1+ with Auto Bed Leveling, bought off Amazon. It is regardless of model. It could be a simplify3D issue, and I will test this....
    Post by: Nicholai Lekson, Jun 25, 2018 in forum: Troubleshooting
  12. Nicholai Lekson
    Thread

    Answered Extruder Stalls and clicks in certain Y location consistently

    Hello, I am currently facing an issue where at a certain Y location I consistently have extruder stalls. Everything works perfectly except this...
    Thread by: Nicholai Lekson, Jun 23, 2018, 15 replies, in forum: Troubleshooting
Showing results 1 to 12 of 12
Search Again