1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Kizmet
    Post

    Robo R2 Z Wizard wont calibrate correctly

    It wont let me mark it as solved, perhaps a mod can help?
    Post by: Kizmet, Nov 24, 2019 in forum: Troubleshooting
  2. Kizmet
    Post

    Robo R2 Z Wizard wont calibrate correctly

    @tkoco @mark tomlinson Thank you for your effort and contribution, honestly given the history of this printer, and its current state of support I...
    Post by: Kizmet, Nov 24, 2019 in forum: Troubleshooting
  3. Kizmet
    Post

    Robo R2 Z Wizard wont calibrate correctly

    @tkoco I think you were on to something here. About the RoboOS and the Marlin Firmware not working well together. Uploaded Marlin.R2.1.1.7.hex...
    Post by: Kizmet, Nov 24, 2019 in forum: Troubleshooting
  4. Kizmet
    Post

    Robo R2 Z Wizard wont calibrate correctly

    Well I'm currently using: 1. RoboOS 2.0.0-r2.6 2. Firmware: Official Marlin_1.1.6_RoboVersion_1.2.4_R2.hex Which versions are known to work?
    Post by: Kizmet, Nov 24, 2019 in forum: Troubleshooting
  5. Kizmet
    Post

    Robo R2 Z Wizard wont calibrate correctly

    Im not using any external software, only the printer controls. If I cant calibrate the bed, theres no point in trying out software to print, is...
    Post by: Kizmet, Nov 24, 2019 in forum: Troubleshooting
  6. Kizmet
    Post

    Robo R2 Z Wizard wont calibrate correctly

    Yes, once the value is negative (in this case -13.45), the bed calibration wizard will start. The problem is, the extruder is way too far away...
    Post by: Kizmet, Nov 24, 2019 in forum: Troubleshooting
  7. Kizmet
    Post

    Robo R2 Z Wizard wont calibrate correctly

    I've also managed to do this via EEPROM Marlin Editor plugin, and saved it. It has to save the value, otherwise the Bed Calibration process would...
    Post by: Kizmet, Nov 24, 2019 in forum: Troubleshooting
  8. Kizmet
    Post

    Robo R2 Z Wizard wont calibrate correctly

    This is also weird, if the Home Z offset is set to 14.2, however if I send M114 (report current position) it reports the following after I hit the...
    Post by: Kizmet, Nov 24, 2019 in forum: Troubleshooting
  9. Kizmet
    Post

    Robo R2 Z Wizard wont calibrate correctly

    I dont understand the printer settings very well, but it seems to me that during bed calibration the value of z-offset is not being read...
    Post by: Kizmet, Nov 24, 2019 in forum: Troubleshooting
  10. Kizmet
    Post

    Robo R2 Z Wizard wont calibrate correctly

    Robo 3D R2 Calibration Log Reset firmware via octoprint web So I sent m520, followed by m500 Send: M502 Recv: echo:Hardcoded Default Settings...
    Post by: Kizmet, Nov 24, 2019 in forum: Troubleshooting
  11. Kizmet
    Post

    Robo R2 Z Wizard wont calibrate correctly

    Im changing the values from the EEPROM Editor via the Printer LCD screen Utilities -> Options -> EEPROM -> Home Offset. Additionally there is no...
    Post by: Kizmet, Nov 24, 2019 in forum: Troubleshooting
  12. Kizmet
    Post

    Robo R2 Z Wizard wont calibrate correctly

    Thanks for the reply =) 1. The bed calibration wizard will refuse to start claiming a default offset of 20 or whatever value was set last: a. if...
    Post by: Kizmet, Nov 22, 2019 in forum: Troubleshooting
  13. Kizmet
    Thread

    Robo R2 Z Wizard wont calibrate correctly

    I just unpacked my kickstarter R2. (It was in storage all this time). The Z axis micro limit switch was caved in (from shipping), had to fix that...
    Thread by: Kizmet, Nov 22, 2019, 45 replies, in forum: Troubleshooting
Showing results 1 to 13 of 13
Search Again