1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. PTIschool
    Post

    Unanswered Reseating Bed Magnets

    So I got the magnets off, so now what epoxy do I need to use?
    Post by: PTIschool, Sep 7, 2021 in forum: Troubleshooting
  2. PTIschool
    Thread

    Unanswered Reseating Bed Magnets

    I have replaced the glass bed on my printer and set the magnets on the bottom of the glass with the 2 part adhesive that is provided with it, but...
    Thread by: PTIschool, Sep 4, 2021, 5 replies, in forum: Troubleshooting
  3. PTIschool
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    Ok, thanks.
    Post by: PTIschool, Mar 31, 2021 in forum: Mods and Upgrades
  4. PTIschool
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    Installed this firmware, but having the same problem as all the other firmwares I install. For some reason the left z stepper goes up and the...
    Post by: PTIschool, Mar 30, 2021 in forum: Mods and Upgrades
  5. PTIschool
    Post

    Unanswered MEGA 2560 R3 replacement

    So I bought the mega replacement and put it in my machine, but my lcd is still showing the hotend at 192 even though its not even plugged in. Any...
    Post by: PTIschool, Mar 8, 2021 in forum: Troubleshooting
  6. PTIschool
    Thread

    Unanswered MEGA 2560 R3 replacement

    Looking for a replacement mega R3 board because I think I fried mine when trying to resolder the data cable connector because it became loose....
    Thread by: PTIschool, Mar 5, 2021, 5 replies, in forum: Troubleshooting
  7. PTIschool
    Post

    Unresolved Extruder assembly smoking!!!

    Ok I will check. Thanks.
    Post by: PTIschool, Feb 24, 2021 in forum: Troubleshooting
  8. PTIschool
    Thread

    Unresolved Extruder assembly smoking!!!

    I have been working on my robo r1+, trying to get it to work after replacing the glass bed and thought I finally had everything figured out, but...
    Thread by: PTIschool, Feb 24, 2021, 3 replies, in forum: Troubleshooting
  9. PTIschool
    Post

    Z Stepper Motor Layout

    Ok cool thanks. Also I am curious about which fan goes where too. So if you could look at that too I would appreciate it.
    Post by: PTIschool, Feb 24, 2021 in forum: General Questions
  10. PTIschool
    Thread

    Z Stepper Motor Layout

    Which is Z motor 1 and which is Z motor 2 on the Robo R1+?
    Thread by: PTIschool, Feb 24, 2021, 4 replies, in forum: General Questions
  11. PTIschool
    Thread

    Unresolved Y axis issues

    I am stilling having an issue with my y axis. I turned down the acceleration from 1300 to 500. I can get it to home now, but It homes in the...
    Thread by: PTIschool, Feb 3, 2021, 1 replies, in forum: Troubleshooting
  12. PTIschool
    Post

    Unresolved Which R1?

    Ok thanks, could you please link the correct firmware I should download?
    Post by: PTIschool, Jan 29, 2021 in forum: Troubleshooting
  13. PTIschool
    Post

    Unresolved Which R1?

    So are you saying i have the “R1+” or “R1+—“ or “R1 PLUS”?
    Post by: PTIschool, Jan 29, 2021 in forum: Troubleshooting
  14. PTIschool
    Post

    Unresolved Which R1?

    R1+ correct?
    Post by: PTIschool, Jan 29, 2021 in forum: Troubleshooting
  15. PTIschool
    Post

    Unresolved Which R1?

    Post by: PTIschool, Jan 29, 2021 in forum: Troubleshooting
  16. PTIschool
    Thread

    Unresolved Which R1?

    If someone could tell me which printer I have, that would be great. I need to know so I make sure I get the right firmware. Here are some...
    Thread by: PTIschool, Jan 29, 2021, 8 replies, in forum: Troubleshooting
  17. PTIschool
    Post

    Unanswered Homing makes loud squealing noise

    Thank you very much.
    Post by: PTIschool, Jan 27, 2021 in forum: Troubleshooting
  18. PTIschool
    Post

    Unanswered Homing makes loud squealing noise

    So I got the firmware to upload, it still squeals a little but not near as bad as when I had other firmware, but still would like to get the sound...
    Post by: PTIschool, Jan 26, 2021 in forum: Troubleshooting
  19. PTIschool
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    Could you upload the firmware you are using? Also what arduino version are you using?
    Post by: PTIschool, Jan 26, 2021 in forum: Mods and Upgrades
  20. PTIschool
    Post

    Unanswered Homing makes loud squealing noise

    That’s what I thought it might be. Any suggestion on normal speed I should have for the y axis?
    Post by: PTIschool, Jan 25, 2021 in forum: Troubleshooting
Showing results 1 to 20 of 22 Next >
Search Again
Page 1 of 2