1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Brock_L
    Post

    Solved Arduino - Extruder Motor Not Working - Robo 3D R1

    Well, I changed out all the stepper drivers and the arduino board. Found out I had two malfunctioning boards to I had to purchase a lot of them...
    Post by: Brock_L, Jul 27, 2016 in forum: Troubleshooting
  2. Brock_L
    Post

    Solved Arduino - Extruder Motor Not Working - Robo 3D R1

    So I've had the new board for a couple days now. Now my problem is that in Arduino, the port selection option is grayed out. I've been researching...
    Post by: Brock_L, Jul 18, 2016 in forum: Troubleshooting
  3. Brock_L
    Post

    Solved Arduino - Extruder Motor Not Working - Robo 3D R1

    Yeah, I'm not getting any type of response in a different port or with a different wire and all of that jazz. I just ordered another board....
    Post by: Brock_L, Jul 12, 2016 in forum: Troubleshooting
  4. Brock_L
    Post

    Solved Arduino - Extruder Motor Not Working - Robo 3D R1

    Unfortunately removing the ramps board didn't help. I'll attach a video as to what I'm seeing happen on my PC while the Arduino is connected....
    Post by: Brock_L, Jul 12, 2016 in forum: Troubleshooting
  5. Brock_L
    Post

    Solved Arduino - Extruder Motor Not Working - Robo 3D R1

    I believe I wired up everything correctly. Pictures will be below I tried to get every angle I could. I did notice when I turned on my Robo 3D,...
    Post by: Brock_L, Jul 12, 2016 in forum: Troubleshooting
  6. Brock_L
    Post

    Solved Arduino - Extruder Motor Not Working - Robo 3D R1

    You bet. I'll try disconnecting everything first and making sure I have everything in the correct pins. Will post in the morning.
    Post by: Brock_L, Jul 11, 2016 in forum: Troubleshooting
  7. Brock_L
    Post

    Solved Arduino - Extruder Motor Not Working - Robo 3D R1

    So, I got the new RAMPS 1.4. And to say I'm lost would be a drastic understatement. The printer doesn't want to connect to MC for some odd...
    Post by: Brock_L, Jul 11, 2016 in forum: Troubleshooting
  8. Brock_L
    Post

    Solved Arduino - Extruder Motor Not Working - Robo 3D R1

    Thanks Mark, Geof, and Danzca6. Tried the stepper driver and still got nothing. Just bought a RAMPS to replace my current one. We'll see how this...
    Post by: Brock_L, Jul 2, 2016 in forum: Troubleshooting
  9. Brock_L
    Post

    Solved Extruder stepper motor Stuck

    When you cooked the E0 port, did you have to replace the entire Arduino or was there a fix?
    Post by: Brock_L, Jun 29, 2016 in forum: Troubleshooting
  10. Brock_L
    Thread

    Solved Arduino - Extruder Motor Not Working - Robo 3D R1

    Hi All. So originally I thought my extruder motor stopped working so I went to my local Microcenter and bought a new motor and wire. As I was...
    Thread by: Brock_L, Jun 29, 2016, 25 replies, in forum: Troubleshooting
  11. Brock_L
    Post

    Solved Extruder stepper motor Stuck

    I'll revive an older post. I had this same problem. Except the motor decided to cut out during a print. I looked around and found out the green...
    Post by: Brock_L, Jan 31, 2016 in forum: Troubleshooting
Showing results 1 to 11 of 11
Search Again