1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. adepino
    Post

    Unanswered Base layer problems....

    The level is definitely pretty close, and stops always look pressed. I watched the video again, but I don't see anything on mine that is alarming....
    Post by: adepino, Aug 22, 2020 in forum: Troubleshooting
  2. adepino
    Post

    Unanswered Base layer problems....

    Ok...So one clue here is that this began immediately after I replaced my Y-axis Pillow Blocks. At that same time, I adjusted the Z-stop switches...
    Post by: adepino, Aug 21, 2020 in forum: Troubleshooting
  3. adepino
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    Is it possible to tell which firmware your Robo R1 is running? I flashed it many years ago and I have no clue whats on there now. Debating on if I...
    Post by: adepino, Aug 21, 2020 in forum: Mods and Upgrades
  4. adepino
    Post

    Unanswered Base layer problems....

    I shimmed with tiny squares of paper between the magnets, that made the most sense to me. The bed is definitely warped though because as I run...
    Post by: adepino, Aug 18, 2020 in forum: Troubleshooting
  5. adepino
    Post

    Unanswered Base layer problems....

    Yes I haven't been on these forums in so long, I just found out about mesh leveling, so I may try that next if I can get it for R1.
    Post by: adepino, Aug 18, 2020 in forum: Troubleshooting
  6. adepino
    Post

    Unanswered Base layer problems....

    Oh I would love to use Simplify3D, but thats a little too rich for my blood haha. I can't justify the cost for the amount I use my printer. Ok,...
    Post by: adepino, Aug 18, 2020 in forum: Troubleshooting
  7. adepino
    Post

    Unanswered Base layer problems....

    Ok, I have been pleased with Cura up to this point. Ive tried to use MatterControls SEVERAL times and really don't like it... What slicer do you...
    Post by: adepino, Aug 18, 2020 in forum: Troubleshooting
  8. adepino
    Post

    Unanswered Base layer problems....

    Hmm...I get how logically, it would appear that the z offset would be causing the problem, but with Cura ive always adjusted the z offset to make...
    Post by: adepino, Aug 18, 2020 in forum: Troubleshooting
  9. adepino
    Post

    Unanswered Base layer problems....

    I don't believe the issue is necessarily related to the Z offset because the first later of brim goes down fairly well. Its when it finishes the...
    Post by: adepino, Aug 18, 2020 in forum: Troubleshooting
  10. adepino
    Thread

    Unanswered Base layer problems....

    Hey guys, I've been printing successfully with my R1 for something like 5-6 years, BUT now this.... First off, both of my "Y axis pillow blocks"...
    Thread by: adepino, Aug 17, 2020, 23 replies, in forum: Troubleshooting
  11. adepino
    Post

    Solved Can anyone tell me whats going on here???

    Thats interesting. Just now I wanted to check it one last time just to see, and it magically fixed itself. This thing is nutty... I did change the...
    Post by: adepino, Apr 8, 2016 in forum: Troubleshooting
  12. adepino
    Post

    Solved Can anyone tell me whats going on here???

    No, I've updated the firmware one time, and I've been printing great with this firmware for probably 9 months or so... It is the first layer that...
    Post by: adepino, Apr 7, 2016 in forum: Troubleshooting
  13. adepino
    Post

    Solved Can anyone tell me whats going on here???

    I never have a problem with bed adhesion, with any material. I've always ran the bed temp on 35-45 for PLA. I've always heard I don't even need...
    Post by: adepino, Apr 7, 2016 in forum: Troubleshooting
  14. adepino
    Post

    Solved Can anyone tell me whats going on here???

    I've changed the Z offset today, but that's common for me. Different filaments work better on different offsets. Like going from PLA to NinjaFlex....
    Post by: adepino, Apr 5, 2016 in forum: Troubleshooting
  15. adepino
    Thread

    Solved Can anyone tell me whats going on here???

    Ive been printing for quite a while now without issue... Then all of a sudden it started doing this. Basically, it will lay the skirt, then the...
    Thread by: adepino, Apr 5, 2016, 9 replies, in forum: Troubleshooting
Showing results 1 to 15 of 15
Search Again