1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Lord_Surl
    Post

    What to avoid?

    Why not?
    Post by: Lord_Surl, Jan 2, 2017 in forum: Printing Filament
  2. Lord_Surl
    Post

    What to avoid?

    Can you recommend a place that sells kits of hardened steel nozzles of various sizes? From what I understand, materials like wood often require a...
    Post by: Lord_Surl, Jan 2, 2017 in forum: Printing Filament
  3. Lord_Surl
    Thread

    What to avoid?

    Obviously one of the big marketing points for the r1 is its ability to print a wide range of materials. However, instead of asking what I CAN use,...
    Thread by: Lord_Surl, Jan 2, 2017, 8 replies, in forum: Printing Filament
  4. Lord_Surl
    Post

    Solved Print does not match model

    Done. It fixed many of my issues for now, but it created a few new ones, such as the holes coming out the wrong size. I can just drill those out...
    Post by: Lord_Surl, Jul 18, 2016 in forum: Troubleshooting
  5. Lord_Surl
    Post

    Solved Print does not match model

    Ok, done. It came out the exact same.
    Post by: Lord_Surl, Jul 12, 2016 in forum: Troubleshooting
  6. Lord_Surl
    Post

    Solved Print does not match model

    Oh, sorry my bad. It's just standard white PLA. Also, it's not warped. A few layers just vanished from the slicing software or something
    Post by: Lord_Surl, Jul 12, 2016 in forum: Troubleshooting
  7. Lord_Surl
    Thread

    Solved Print does not match model

    Hello all, So I was trying to print out a part in two halves, with each half being essentially an arch. Now, when combined, the two arches...
    Thread by: Lord_Surl, Jul 12, 2016, 8 replies, in forum: Troubleshooting
  8. Lord_Surl
    Post

    Unresolved Why is this happening:(

    As was said above, your z axis height seems to be a bit too high. You can easily edit this in the settings. Just keep decreasing it by small...
    Post by: Lord_Surl, Jul 12, 2016 in forum: Troubleshooting
  9. Lord_Surl
    Post

    Unanswered Not printing where MC shows model on table - Also offset question

    Do yourself a huge favor and ditch MC in favor of Cura. It'll save you tons of time and frustration, as well as probably fixing your problem. If...
    Post by: Lord_Surl, Jul 12, 2016 in forum: Troubleshooting
  10. Lord_Surl
    Post

    Solved Temp Fail

    I had the same problem for the longest time. Turns out I didn't wrap my thermistor up enough (I had one of the older models) and the fan was...
    Post by: Lord_Surl, Jul 12, 2016 in forum: Troubleshooting
  11. Lord_Surl
    Post

    Solved Out of the blue hardware error

    Well, either way I need to get the old one out first. Preferably in a way that doesn't break it any more than it already is.
    Post by: Lord_Surl, Jun 27, 2016 in forum: Troubleshooting
  12. Lord_Surl
    Post

    Solved Out of the blue hardware error

    [ATTACH] Well, shit. I started tracing the wires, and I noticed the broken wire. God damnit. I don't suppose you know of an easy way to dig out...
    Post by: Lord_Surl, Jun 27, 2016 in forum: Troubleshooting
  13. Lord_Surl
    Thread

    Solved Out of the blue hardware error

    Hello everyone! So, I've had my robo3d for awhile now. I had quite a few issues on start up, but when all those were resolved, it worked...
    Thread by: Lord_Surl, Jun 27, 2016, 6 replies, in forum: Troubleshooting
Showing results 1 to 13 of 13
Search Again