1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by afat08

  1. afat08
    Post

    Solved Bottom layer coming weird?

    Infill overlap possibly?
    Post by: afat08, Feb 25, 2016 in forum: Troubleshooting
  2. afat08
    Post

    Unresolved Busted a part. :(

    This seems like something I should print just to have on hand, even if under warranty, it would get me through until Robo can replace it...?
    Post by: afat08, Feb 25, 2016 in forum: Troubleshooting
  3. afat08
    Post

    Unresolved Wierd Problem

    I have noticed recently that this problem is mainly cause when printing overhangs or when trying to go up and out at the same time...
    Post by: afat08, Feb 25, 2016 in forum: Troubleshooting
  4. afat08
    Post

    NinjaFlex filament

    [MEDIA] Pretty good video showing the settings for printing with the ninjaflex
    Post by: afat08, Feb 16, 2016 in forum: Printing Filament
  5. afat08
    Post

    Unresolved Wierd Problem

    BUMP...Just picked up my digital calipers and ran a 20mm test cube. It came out almost dead accurate within +/- .03 mm tolerance. And the extruder...
    Post by: afat08, Feb 16, 2016 in forum: Troubleshooting
  6. afat08
    Post

    Unanswered Help with Cura Settings

    When I did mine, I sat there running first layer after first layer and cleaning the bed each and every time until I finally had it fine tuned....
    Post by: afat08, Feb 12, 2016 in forum: Troubleshooting
  7. afat08
    Post

    Unresolved Bed Not Returning to 0 degrees when printing with SD card

    If your bed remains at the same print temp then you have a problem, but if it simply is just not going to 0, it probably won't unless your room...
    Post by: afat08, Feb 12, 2016 in forum: Troubleshooting
  8. afat08
    Post

    Unresolved Cure: no supports being printed?

    Layout looks different from mine, but the support settings appear to be the same and I have no problems with printing supports so this is beyond...
    Post by: afat08, Feb 8, 2016 in forum: Troubleshooting
  9. afat08
    Post

    Unresolved Cure: no supports being printed?

    What do you have your "Expert Config" set at (the three "..." button next to it)?
    Post by: afat08, Feb 5, 2016 in forum: Troubleshooting
  10. afat08
    Post

    Unresolved Issues with vertical circles

    [ATTACH]
    Post by: afat08, Feb 3, 2016 in forum: Troubleshooting
  11. afat08
    Post

    Unresolved Nozzel rubs plastic as it travels causing strings.

    Give Cura a shot. I've only used MC and Cura, so I can't comment on the rest, but I definitely prefer Cura and havn't had a problem with it yet...
    Post by: afat08, Feb 2, 2016 in forum: Troubleshooting
  12. afat08
    Post

    E3D v6 Information, Installation Guides, and Review

    I got mine from them and it came with everything, small piece of tubing as well
    Post by: afat08, Feb 2, 2016 in forum: Mods and Upgrades
  13. afat08
    Post

    Solved extruder clog on r1 plus+, can't remove hot end

    I just went through this with mine, because all the information I find is for the older version. What I found when taking mine apart is that the...
    Post by: afat08, Feb 2, 2016 in forum: Troubleshooting
  14. afat08
    Post

    Unresolved Wierd Problem

    Sorry, I was very busy over the weekend and could not get a good pic or video to show what is happening. I will try today or tomorrow...Just by...
    Post by: afat08, Feb 1, 2016 in forum: Troubleshooting
  15. afat08
    Post

    Solved Extruder heating up, then cooling back down when it starts to print.

    Drop the bed temp down to 70 and try that
    Post by: afat08, Jan 31, 2016 in forum: Troubleshooting