1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Aflickted

  1. Aflickted
    Post

    Unresolved Gcode Question

    Redrex 310mm T8x8 Lead Screw Integrated with Nema 17 Stepper Motor 1.5A 40Ncm/57.1 oz.in for Prusa i3 Reprap Corexy DIY 3D Printer kits and CNC...
    Post by: Aflickted, Jan 18, 2018 in forum: Troubleshooting
  2. Aflickted
    Post

    Unresolved Gcode Question

    So I think my pitch is 8mm (4 thread start with 2mm spacing). My motor step angle is 1.2Degrees. How do i find.. Driver Microstepping? Pitch...
    Post by: Aflickted, Jan 18, 2018 in forum: Troubleshooting
  3. Aflickted
    Post

    Unresolved Gcode Question

    Thanks Mark. That’s really all I can do at this point. I’ve already done the PID tuning, extruder calibration and all the other little checks I...
    Post by: Aflickted, Jan 18, 2018 in forum: Troubleshooting
  4. Aflickted
    Post

    Unresolved Gcode Question

    Both of mine are R1's. I don't have anything else except those two printers. Yeah, I don't think it's Z banding but I'm at a loss right now. I do...
    Post by: Aflickted, Jan 18, 2018 in forum: Troubleshooting
  5. Aflickted
    Post

    Unresolved Gcode Question

    [IMG] This is the same gcode and model from my other printer. This is how it is supposed to look... lol I appreciate the help. I apologize for...
    Post by: Aflickted, Jan 18, 2018 in forum: Troubleshooting
  6. Aflickted
    Post

    Unresolved Gcode Question

    Hey guys. So I did what I was asked. 1. Made a new profile. 2. Sliced and saved a new .gcode to a new SD card AND printed from computer....
    Post by: Aflickted, Jan 18, 2018 in forum: Troubleshooting
  7. Aflickted
    Post

    Unresolved Gcode Question

    My stepper motor [IMG] So I would change the 3rd value to 400? Instead of the robo‘s kit 1600? Or am I missing an input number? I’m sorry for...
    Post by: Aflickted, Jan 16, 2018 in forum: Troubleshooting
  8. Aflickted
    Post

    Unresolved Gcode Question

    Screw has four thread starts, spaced 2mm apart, for an 8mm pitch. I have that thread saved. I almost went back with threaded rods but they were...
    Post by: Aflickted, Jan 15, 2018 in forum: Troubleshooting
  9. Aflickted
    Post

    Unresolved Gcode Question

    I didn’t buy their upgrade. I bought the same kind of leadscrew though. So I would use the R1+ on the leadscrew updated one and the normal on the...
    Post by: Aflickted, Jan 15, 2018 in forum: Troubleshooting
  10. Aflickted
    Post

    Unresolved Gcode Question

    Which do i use? 1,2 or 3? [IMG] Sent from my iPhone using Tapatalk
    Post by: Aflickted, Jan 15, 2018 in forum: Troubleshooting
  11. Aflickted
    Post

    Unresolved Gcode Question

    So enable EEPROM Thermistor 5 Hot end max temp Should be all I change? I did do the microstepping but I never use it so I’m not worried about...
    Post by: Aflickted, Jan 15, 2018 in forum: Troubleshooting
  12. Aflickted
    Post

    Unresolved Gcode Question

    I'm only replacing the threaded rods with leadscrews because i have to replace the threaded rods anyway. I figured why go back with threaded rod.
    Post by: Aflickted, Jan 15, 2018 in forum: Troubleshooting
  13. Aflickted
    Post

    Unresolved Gcode Question

    ok both of mine have threaded rods...for now. one is getting upgraded in the next few days. I have the lead screws. So I should upload the stock...
    Post by: Aflickted, Jan 15, 2018 in forum: Troubleshooting
  14. Aflickted
    Post

    Unresolved Gcode Question

    Correct, both are R1. R1+ have the good lead screws right?
    Post by: Aflickted, Jan 15, 2018 in forum: Troubleshooting
  15. Aflickted
    Post

    Unresolved Gcode Question

    So this could be some be some of my problem? Bad firmware? I use this on both printers. I thought I got it off the Robo website when I got the E3D...
    Post by: Aflickted, Jan 15, 2018 in forum: Troubleshooting