1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by albert3d

  1. albert3d
    Post

    Red robo r2

    That's brilliant. I can't believe nobody here has done something like that prior. What type of paint did you use? Did you have to sand and/or...
    Post by: albert3d, Apr 2, 2021 in forum: Show and Tell
  2. albert3d
    Post

    Improved Bushing holders

    Will you be updating this on Thingiverse (or some other stl repository that doesn't run slower than molasses)? :)
    Post by: albert3d, Mar 25, 2020 in forum: Mods and Upgrades
  3. albert3d
    Post

    Flexplate system for the R2 Printer

    Good tip. Also, Buildtak slashed their prices the end of last year on their flex systems. So you can get the R2 flex system now for $66.50...
    Post by: albert3d, Jan 31, 2020 in forum: Mods and Upgrades
  4. albert3d
    Post

    Replacing bushing covers on x/y axis rods

    4 bearings or 4 sets? Looks like they have 6 sets of 4 for the 6mm ones.
    Post by: albert3d, Nov 28, 2019 in forum: Troubleshooting
  5. albert3d
    Post

    Replacing bushing covers on x/y axis rods

    What about these? https://www.ebay.com/ulk/itm/153552765087
    Post by: albert3d, Nov 27, 2019 in forum: Troubleshooting
  6. albert3d
    Post

    R1+'s for Sale

    Reading the Shoutbox, looks like $300 shipped. Not a bad deal for new in box and free shipping.
    Post by: albert3d, Nov 13, 2019 in forum: ROBO 3D News and Announcements
  7. albert3d
    Post

    Unresolved LCD Screen Non-responsive

    Could be a bad SD in the PI as well. So if you already reimaged the SD, you may want to try another just in case before replacing the PI. Also...
    Post by: albert3d, Nov 12, 2019 in forum: Troubleshooting
  8. albert3d
    Post

    Solved Mystery Part?

    yeah that's a filament cleaner/oiler. You put it on top of the extruder where the filament goes in and just pass the filament through it. The...
    Post by: albert3d, Nov 12, 2019 in forum: General Questions
  9. albert3d
    Post

    Waiting for support from robo

    Agreed. Reach out to Jonah and Hannah at partsbuilt.com. They do have the R2 board on their site, but it isn't in stock yet. Not sure if they...
    Post by: albert3d, Oct 31, 2019 in forum: Community Recomendations
  10. albert3d
    Post

    Head Crashing

    Partbuilt is going to be the life blood of these machines the way they are going. Just checked their inventory again this week and can't believe...
    Post by: albert3d, Oct 29, 2019 in forum: Troubleshooting
  11. albert3d
    Post

    I just want to replace the hot end.

    ok. As long as the NTC Thermistor has the same data table as the thermistor the stock robo uses, you should be ok. If not, your temps might be...
    Post by: albert3d, Oct 21, 2019 in forum: Mods and Upgrades
  12. albert3d
    Post

    I just want to replace the hot end.

    Did you use their heater cartridge and thermistor or did you use the stock ones? If you used theirs, then did they have the same connectors to go...
    Post by: albert3d, Oct 21, 2019 in forum: Mods and Upgrades
  13. albert3d
    Post

    Bed cover/tape

    Black sharpie over the light colored tape if in a pinch? :) I like the buildtak sheets now. Kind of thinking of getting a flexplate system though.
    Post by: albert3d, Oct 21, 2019 in forum: Troubleshooting
  14. albert3d
    Post

    Solved Metric or Imperial smooth rods

    Partbuilt3d has the chromed hardened rods that are a slight improvement over stock or stainless. They are also cheaper than their stainless. He...
    Post by: albert3d, Oct 21, 2019 in forum: General Questions
  15. albert3d
    Post

    Solved Screen Looks Weird After Firmware Update

    For reference, what firmware version were you seeing this issue?
    Post by: albert3d, Oct 3, 2019 in forum: Troubleshooting