1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by BrooklynBay

  1. BrooklynBay
    Post

    Unresolved Robo 3d R1+ rewired strange issue

    Did you check the servo motors & wiring for shorts? You could unplug one motor at a time to see if the issue persists.
    Post by: BrooklynBay, Jun 1, 2020 at 7:12 PM in forum: Troubleshooting
  2. BrooklynBay
    Post

    Unresolved Robo 3d R1+ rewired strange issue

    Make sure that you're installing the correct version of the firmware.
    Post by: BrooklynBay, May 31, 2020 at 10:00 PM in forum: Troubleshooting
  3. BrooklynBay
    Post

    Small gaps while printing petg

    Do you get a better print with another brand or even a different type of filament such as PLA? I've printed the same item multiple times with...
    Post by: BrooklynBay, Mar 9, 2020 in forum: Printing Filament
  4. BrooklynBay
    Post

    Bed replacement on R1 beta

    The kickstarter page said that it was originally available as a kit with a 10x10x8 print size. Why did they reduce the print size to 10x9x8?
    Post by: BrooklynBay, Feb 9, 2020 in forum: Projects
  5. BrooklynBay
    Post

    Bed replacement on R1 beta

    Were the bed parts printed with ABS or PETG?
    Post by: BrooklynBay, Feb 9, 2020 in forum: Projects
  6. BrooklynBay
    Post

    Bed replacement on R1 beta

    The MOSFET controller is a good modification. It takes the amp load off of the RAMPS, and will save the RAMPS in the event that the bed wiring...
    Post by: BrooklynBay, Feb 9, 2020 in forum: Projects
  7. BrooklynBay
    Post

    Newbie to the site, but not the printer. Got questions...

    The heater block is leaking from the heat break connection. This happens when the nozzle is either the wrong depth or it's not making contact with...
    Post by: BrooklynBay, Jan 26, 2020 in forum: General Questions
  8. BrooklynBay
    Post

    Solved Noisy Fan fix?

    The firmware will need to be edited to a higher number since it's preset at these values. 40 watt heaters have red wires, and 50 watt heaters have...
    Post by: BrooklynBay, Jan 26, 2020 in forum: General Questions
  9. BrooklynBay
    Post

    Solved Noisy Fan fix?

    I believe that the extruder's limit is 290°, and the bed is 110°. Set your limits a few degrees lower to allow for temperature fluctuations.
    Post by: BrooklynBay, Jan 26, 2020 in forum: General Questions
  10. BrooklynBay
    Post

    Newbie to the site, but not the printer. Got questions...

    The original version of Matter Control from Robo was 1.5 which you have but it had a file to replace the view of the print bed with a Robo logo....
    Post by: BrooklynBay, Jan 26, 2020 in forum: General Questions
  11. BrooklynBay
    Post

    Newbie to the site, but not the printer. Got questions...

    I use Matter Control version 1.7.5 with Windows 7. It was running on Windows Vista before my SSD crashed. I've used version 2 one time but prefer...
    Post by: BrooklynBay, Jan 25, 2020 in forum: General Questions
  12. BrooklynBay
    Post

    Newbie to the site, but not the printer. Got questions...

    Test all of the servo wiring from point to point with a continuity tester. Maybe one wire has a bad or open connection so it doesn't allow the...
    Post by: BrooklynBay, Jan 25, 2020 in forum: General Questions
  13. BrooklynBay
    Post

    Solved Thermal Runaway

    The stock extruder fan is 25mm. I also have the upgraded bracket with a 40mm fan. The issue you're describing is similar to what I was...
    Post by: BrooklynBay, Jan 18, 2020 in forum: Troubleshooting
  14. BrooklynBay
    Post

    Newbie to the site, but not the printer. Got questions...

    Does the Johnny 5 robot in the photo above have servos or solenoids to move the arms, grippers or any other parts?
    Post by: BrooklynBay, Jan 18, 2020 in forum: General Questions
  15. BrooklynBay
    Post

    Replacement for Build Plate

    The glass door on a lot of toaster ovens is 10" x 15" which fits perfectly over your existing glass bed. I have two of these glass doors. One is a...
    Post by: BrooklynBay, Jan 11, 2020 in forum: Mods and Upgrades