1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by DaveKerk

  1. DaveKerk
    Post

    A few issues...

    Ok I finally had more time to sit down with this thing... The Firmware Update option isn't finding the HEX file on the USB. I'm thinking it's...
    Post by: DaveKerk, Oct 30, 2019 in forum: Troubleshooting
  2. DaveKerk
    Post

    A few issues...

    Also I don't ever know if the firmware finishes. When I try updating it, it will often tell me to reset printer controls or that the bed isn't...
    Post by: DaveKerk, Oct 18, 2019 in forum: Troubleshooting
  3. DaveKerk
    Post

    A few issues...

    Thank you very much, I really appreciate the help. I feel like a rollback of the firmware will do the trick.
    Post by: DaveKerk, Oct 18, 2019 in forum: Troubleshooting
  4. DaveKerk
    Post

    A few issues...

    Yayyy.... I remembered reading something along the lines of that. haha first Robo then Lulzbot...
    Post by: DaveKerk, Oct 18, 2019 in forum: Troubleshooting
  5. DaveKerk
    Post

    A few issues...

    Thank you for your help. I wish I could contact support and just get fresh direct from them. Both an SD image and the firmware. I'll keep...
    Post by: DaveKerk, Oct 18, 2019 in forum: Troubleshooting
  6. DaveKerk
    Post

    A few issues...

    Also another note... after setting the EEPROM to -10, I had to hard reset the machine and it reset to -20 again.
    Post by: DaveKerk, Oct 18, 2019 in forum: Troubleshooting
  7. DaveKerk
    Post

    A few issues...

    So forgive the ignorance... my previous firmware files were .hex files. I do have the SD card image that is a zip with an .img... a little help on...
    Post by: DaveKerk, Oct 18, 2019 in forum: Troubleshooting
  8. DaveKerk
    Post

    A few issues...

    Or I might have 1.2.4. Looks like Marlin 1.1.6 and RoboVersion 1.2.4
    Post by: DaveKerk, Oct 18, 2019 in forum: Troubleshooting
  9. DaveKerk
    Post

    A few issues...

    I set it to -10 then tried I do mean firmware, that is what borked the thing after I redid the SD Card change. As far as I can tell anyway... the...
    Post by: DaveKerk, Oct 18, 2019 in forum: Troubleshooting
  10. DaveKerk
    Post

    A few issues...

    I'll try -10 but when I set it to -2 it didn't work. It did let me try the fine tune but it just froze at the first step as well.
    Post by: DaveKerk, Oct 18, 2019 in forum: Troubleshooting
  11. DaveKerk
    Thread

    A few issues...

    Hi everyone, I am having a handful of issues with my R2. So this all started after I didn't use the printer for a little while. A month or two. I...
    Thread by: DaveKerk, Oct 18, 2019, 23 replies, in forum: Troubleshooting
  12. DaveKerk
    Thread

    DIY Dual Extruder Upgrade

    Hey all, I want to get my Robo R2 to be a dual extruder. I can buy the hot end from another supplier. I use Simplify3D. Simplify3D has options to...
    Thread by: DaveKerk, Aug 8, 2019, 3 replies, in forum: Mods and Upgrades
  13. DaveKerk
    Post

    Y-Axis Belt Seems Loose

    Hi everyone, just coming back to conclude the story. I was able to get a new set of bearings via Robo. After disassembling it and replacing the...
    Post by: DaveKerk, Apr 19, 2019 in forum: Troubleshooting