1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by DavidHooie

  1. DavidHooie
    Post

    Partial Answer R1+ Can't maintain temperature on Extruder

    Thanks, I appreciate your opinion because I'm a noobie still and also because that software would run me $150 or so. I know my printer has the...
    Post by: DavidHooie, Jul 14, 2017 in forum: Troubleshooting
  2. DavidHooie
    Post

    Partial Answer R1+ Can't maintain temperature on Extruder

    I'm looking at Simplify 3D because I've heard great things and part of me wonders if some of my issues aren't just from the way MatterControl...
    Post by: DavidHooie, Jul 14, 2017 in forum: Troubleshooting
  3. DavidHooie
    Post

    Partial Answer R1+ Can't maintain temperature on Extruder

    May I ask what you use?
    Post by: DavidHooie, Jul 14, 2017 in forum: Troubleshooting
  4. DavidHooie
    Post

    Partial Answer R1+ Can't maintain temperature on Extruder

    Hey Geof, Yes, all stock stuff right now. I assume there's a place in MatterControl to turn the fan speed down? Can you point me to the right place?
    Post by: DavidHooie, Jul 14, 2017 in forum: Troubleshooting
  5. DavidHooie
    Post

    Partial Answer R1+ Can't maintain temperature on Extruder

    I'll check the connections on the RAMPS board first since I just swapped that out, but this problem was going on before that. So maybe the harness...
    Post by: DavidHooie, Jul 14, 2017 in forum: Troubleshooting
  6. DavidHooie
    Thread

    Partial Answer R1+ Can't maintain temperature on Extruder

    I've been battling this issue ever since I got the printer 2 months ago. I've yet to be able to print more than 2 things in a row before the...
    Thread by: DavidHooie, Jul 14, 2017, 15 replies, in forum: Troubleshooting
  7. DavidHooie
    Post

    Solved Robo R1+ New RAMPS board - think I goofed something with the Z axis

    Thanks Mark! I'll check that out tonight when I get home from work! I assume the nut on the mount is the small one pointing toward the left side...
    Post by: DavidHooie, Jul 10, 2017 in forum: Troubleshooting
  8. DavidHooie
    Post

    Solved Robo R1+ New RAMPS board - think I goofed something with the Z axis

    I think the problem may be with the End Stop on the right hand side. There's a "nut" that keeps spinning down loose and throwing off the leveling...
    Post by: DavidHooie, Jul 9, 2017 in forum: Troubleshooting
  9. DavidHooie
    Post

    Solved Robo R1+ New RAMPS board - think I goofed something with the Z axis

    Thanks Mark! Do you know if you're facing the front of the printer, is the Z Motor on the right-hand side Z motor 2? Gives me a place to look!
    Post by: DavidHooie, Jul 8, 2017 in forum: Troubleshooting
  10. DavidHooie
    Thread

    Solved Robo R1+ New RAMPS board - think I goofed something with the Z axis

    I received a new RAMPS board from ROBO, I swapped the cables from the old board to the new one but now the X and Y axis move perfectly in both...
    Thread by: DavidHooie, Jul 8, 2017, 9 replies, in forum: Troubleshooting