1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Disturbinglee

  1. Disturbinglee
    Post

    Partial Answer ABS Benchy

    Yeah haha! If I can get it to stick better now I'm good. I'm adding some brims attached to the benchy to see how it prints. Then the rest of this...
    Post by: Disturbinglee, Feb 15, 2018 in forum: Troubleshooting
  2. Disturbinglee
    Post

    Partial Answer ABS Benchy

    Okay I called matter hackers and he was shocked that it would print at 210 they're sending me a new roll. Sent from my iPhone using Tapatalk
    Post by: Disturbinglee, Feb 15, 2018 in forum: Troubleshooting
  3. Disturbinglee
    Post

    Partial Answer ABS Benchy

    It was going great till this happened. The base of it warped and came up so it does still have that property when cooled so much. But that makes...
    Post by: Disturbinglee, Feb 15, 2018 in forum: Troubleshooting
  4. Disturbinglee
    Post

    Partial Answer ABS Benchy

    So far it is printing a benchy fantastically at 210 with the fan at 100% It seems like it does dissolve in acetone but I do not have an extra...
    Post by: Disturbinglee, Feb 15, 2018 in forum: Troubleshooting
  5. Disturbinglee
    Post

    Partial Answer ABS Benchy

    I do have some other filament, I'll try printing at 210 first. Fan full speed? Sent from my iPhone using Tapatalk
    Post by: Disturbinglee, Feb 15, 2018 in forum: Troubleshooting
  6. Disturbinglee
    Post

    Partial Answer ABS Benchy

    So you know also, it appears as though the print head pulls on the edge of the triangle that supports the bridge as it is going by it. So maybe...
    Post by: Disturbinglee, Feb 14, 2018 in forum: Troubleshooting
  7. Disturbinglee
    Post

    Partial Answer ABS Benchy

    It does extrude at 200, and it seems to extrude well at 200.. ill bring the temperature down by 20 at all of the layers, trying again now. It...
    Post by: Disturbinglee, Feb 14, 2018 in forum: Troubleshooting
  8. Disturbinglee
    Post

    Partial Answer ABS Benchy

    I will try that when I get back tonight and I will let you know how it goes. Thank you for all your help! Sent from my iPhone using Tapatalk
    Post by: Disturbinglee, Feb 14, 2018 in forum: Troubleshooting
  9. Disturbinglee
    Post

    Partial Answer ABS Benchy

    The filament is MatterHackers new build series ABS Orange It wont let me upload the link because I am still new to the forum and I have not made 3...
    Post by: Disturbinglee, Feb 14, 2018 in forum: Troubleshooting
  10. Disturbinglee
    Post

    Partial Answer ABS Benchy

    This is how the temperature test came out.. not so good.. Best results fur bridging at 235 but still not good. Any tips? Would it help if I...
    Post by: Disturbinglee, Feb 14, 2018 in forum: Troubleshooting
  11. Disturbinglee
    Thread

    Partial Answer ABS Benchy

    Hi everyone, I am attempting to print a benchy with ABS, I know there are better filaments out there but I am trying to get better at printing...
    Thread by: Disturbinglee, Feb 13, 2018, 21 replies, in forum: Troubleshooting