1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Domenic

  1. Domenic
    Post

    Partial Answer Layer lines on my prints are not even

    So replaced the belt on the X and the Y axes and there was no change. Prints still look the same. I'm pretty much out of ideas except the rods on...
    Post by: Domenic, Jan 4, 2019 in forum: Troubleshooting
  2. Domenic
    Post

    Partial Answer Layer lines on my prints are not even

    Ok, do you know the specific type of belt I need to get? Or does it not matter
    Post by: Domenic, Dec 15, 2018 in forum: Troubleshooting
  3. Domenic
    Post

    Partial Answer Layer lines on my prints are not even

    So I have done almost everything in the book. I would say the only thing left that I could try is replacing the smooth rods on the X and Y axes,...
    Post by: Domenic, Dec 15, 2018 in forum: Troubleshooting
  4. Domenic
    Post

    Partial Answer Layer lines on my prints are not even

    Yes I have calibrated it, but I guess it can’t hurt to do it again. What do you mean by loose drive component?
    Post by: Domenic, Dec 9, 2018 in forum: Troubleshooting
  5. Domenic
    Post

    Partial Answer Layer lines on my prints are not even

    Wow that’s a nice little contraption lol. So I did that on my x axis and nothing really changed. I also changed my nozzle to a .25mm nozzle and...
    Post by: Domenic, Dec 9, 2018 in forum: Troubleshooting
  6. Domenic
    Post

    Partial Answer Layer lines on my prints are not even

    So I replaced all the bearings except for two on the left Z axis. Still getting the same results. Anyone know of a good belt tensioner as my old...
    Post by: Domenic, Dec 7, 2018 in forum: Troubleshooting
  7. Domenic
    Post

    Partial Answer Layer lines on my prints are not even

    Ok thanks, I’ll order the new bearings today. You said that I need to print a new holder even if they are from amazon?
    Post by: Domenic, Nov 25, 2018 in forum: Troubleshooting
  8. Domenic
    Post

    Partial Answer Layer lines on my prints are not even

    Ok, makes sense. Quick question, to take them apart do I need to go underneath the printer?
    Post by: Domenic, Nov 25, 2018 in forum: Troubleshooting
  9. Domenic
    Post

    Partial Answer Layer lines on my prints are not even

    Ok thank you so much, I will try this. Do you think I could use the bushing bearing model that I habe seen someone post on another thread?
    Post by: Domenic, Nov 25, 2018 in forum: Troubleshooting
  10. Domenic
    Post

    Partial Answer Layer lines on my prints are not even

    R1+
    Post by: Domenic, Nov 25, 2018 in forum: Troubleshooting
  11. Domenic
    Post

    Partial Answer Layer lines on my prints are not even

    I did notice that my bed wobbles side to side slightly when I try to move it side to side. I guess I’ll attack that next, how should I go about that?
    Post by: Domenic, Nov 25, 2018 in forum: Troubleshooting
  12. Domenic
    Post

    Partial Answer Layer lines on my prints are not even

    I feel like I have tried everything in the book, extruder calibration, loose belts, and now I am gonna manually change temp and e steps throughout...
    Post by: Domenic, Nov 25, 2018 in forum: Troubleshooting
  13. Domenic
    Post

    Partial Answer Layer lines on my prints are not even

    I have but not in a while, and is there a way to know how tight the belts should be?
    Post by: Domenic, Nov 22, 2018 in forum: Troubleshooting
  14. Domenic
    Thread

    Partial Answer Layer lines on my prints are not even

    So for a long tome now my layers have been “misaligned” I’m not quite sure how to explain it except layer lines. At first I thought it was z...
    Thread by: Domenic, Nov 22, 2018, 36 replies, in forum: Troubleshooting