1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Element18592

  1. Element18592
    Post

    Partially Solved Layer separation issue

    I wrapped the E3Ds heater block with Kapton tape with the intention of retaining heat and preventing possible interference from the parts fan. In...
    Post by: Element18592, Dec 1, 2018 in forum: Troubleshooting
  2. Element18592
    Post

    Partially Solved Layer separation issue

    My parts fan kicks on after the 2nd layer is finished. Still a good while before the failure ever occurs. I'm running the Robo3DR1V3 firmware....
    Post by: Element18592, Nov 29, 2018 in forum: Troubleshooting
  3. Element18592
    Post

    Partially Solved Layer separation issue

    Okay so while running the printer wired with the LCD controller disconnected, luckily I was prompted with an error dialog telling me exactly what...
    Post by: Element18592, Nov 29, 2018 in forum: Troubleshooting
  4. Element18592
    Post

    Partially Solved Layer separation issue

    No strange noises. I've jogged the printer up and down around the height of the constant failure and didn't notice anything out of the ordinary. I...
    Post by: Element18592, Nov 29, 2018 in forum: Troubleshooting
  5. Element18592
    Post

    Partially Solved Layer separation issue

    I don't do it often as I've never had a jam since installing the E3D hot end years back. I did take note of your previous post though and slipped...
    Post by: Element18592, Nov 29, 2018 in forum: Troubleshooting
  6. Element18592
    Post

    Partially Solved Layer separation issue

    Brand new spool of Robo brand filament. Issue occurred again at right about the same layer. [IMG]
    Post by: Element18592, Nov 29, 2018 in forum: Troubleshooting
  7. Element18592
    Post

    Partially Solved Layer separation issue

    That was one of the first thing that crossed my mind, however the issue happens at the same layer across multiple models.
    Post by: Element18592, Nov 29, 2018 in forum: Troubleshooting
  8. Element18592
    Thread

    Partially Solved Layer separation issue

    I have a Robo R1 and it's worked flawlessly for me for the years I've owned it. These last couple of prints I've done have all had the exact same...
    Thread by: Element18592, Nov 28, 2018, 19 replies, in forum: Troubleshooting
  9. Element18592
    Thread

    3D Printed Portable Nintendo 64

    So i recently finished my latest project, ive made a few portables in the past from and Xbox 360 laptop to a Raspberry Pi based Gameboy DMG mod. I...
    Thread by: Element18592, Jun 8, 2016, 0 replies, in forum: Projects
  10. Element18592
    Post

    Partially Solved Robo 3D R1 Level on Some parts of the bed?

    Just to clarify, that wasn't the fix, and this random fix came a few bad prints after the next day. So it's not like I checked my magnet count,...
    Post by: Element18592, Mar 29, 2016 in forum: Troubleshooting
  11. Element18592
    Post

    Partially Solved Robo 3D R1 Level on Some parts of the bed?

    Not sure what happened but i printed something today and it came out perfect. I literally did nothing different than i have been doing. Its even...
    Post by: Element18592, Mar 17, 2016 in forum: Troubleshooting
  12. Element18592
    Post

    Partially Solved Robo 3D R1 Level on Some parts of the bed?

    Thats actually one of the first things i did, i forgot to mention it in the original post. When i increased it, it allowed it to print yes, but it...
    Post by: Element18592, Mar 15, 2016 in forum: Troubleshooting
  13. Element18592
    Post

    Partially Solved Robo 3D R1 Level on Some parts of the bed?

    I just used my callipers and both ends were nearly perfectly even i only had to make a small hair adjustment to one of the rods to get it where i...
    Post by: Element18592, Mar 12, 2016 in forum: Troubleshooting