1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by GAmbrosio

  1. GAmbrosio
    Post

    Adding my thanks.

    Funny, it may be subliminal, but I was considering a second printer and looked at the Wanhao i3 and 4s :) Sent from my iPhone using Tapatalk
    Post by: GAmbrosio, Jun 2, 2016 in forum: Show and Tell
  2. GAmbrosio
    Post

    Adding my thanks.

    Daniel had some bad luck with the two Robos including one he won as a draw/raffle. Bummer. But he seems to pitch the Wanhao a lot on the ROBO...
    Post by: GAmbrosio, Jun 2, 2016 in forum: Show and Tell
  3. GAmbrosio
    Post

    Solved Possible minor Z-axis issue?

    Sample PLA, general consensus is that this material sucks or at least not the best or better to expect great results may be reaching- try a better...
    Post by: GAmbrosio, Jun 2, 2016 in forum: Troubleshooting
  4. GAmbrosio
    Post

    Unanswered Overhangs and printing with support

    Geof, this, helped a lot. This and orienting the model to actually be realistically printable. Sent from my iPhone using Tapatalk
    Post by: GAmbrosio, May 31, 2016 in forum: General Questions
  5. GAmbrosio
    Post

    Unanswered Y-Axis stepper motor roughness

    if you got it this way from purchase contact Robo and get a new one under warranty. Sent from my iPhone using Tapatalk
    Post by: GAmbrosio, May 23, 2016 in forum: Troubleshooting
  6. GAmbrosio
    Post

    Unanswered Simplify3d

    One thing to realize is that the markings on the bed makes no real world correspondence. Meaning they are phantoms. What's going on with the z...
    Post by: GAmbrosio, May 23, 2016 in forum: General Questions
  7. GAmbrosio
    Post

    Unanswered Overhangs and printing with support

    It does it regardless of type of PLA and various temps, it may just be the orientation of the model, it is a Star Trek voyager from Thingiverse...
    Post by: GAmbrosio, May 22, 2016 in forum: General Questions
  8. GAmbrosio
    Post

    Unanswered Overhangs and printing with support

    How do I re level? :) Sent from my iPhone using Tapatalk
    Post by: GAmbrosio, May 22, 2016 in forum: General Questions
  9. GAmbrosio
    Post

    Unanswered Overhangs and printing with support

    That was at 200 ppla. Sent from my iPhone using Tapatalk
    Post by: GAmbrosio, May 22, 2016 in forum: General Questions
  10. GAmbrosio
    Post

    Unanswered Overhangs and printing with support

    Dang, shook it...[IMG] Sent from my iPhone using Tapatalk
    Post by: GAmbrosio, May 22, 2016 in forum: General Questions
  11. GAmbrosio
    Post

    Unanswered Overhangs and printing with support

    Geof, here's a pic of what it looks like right on the layer that the supports were removed from. [IMG] Sent from my iPhone using Tapatalk
    Post by: GAmbrosio, May 22, 2016 in forum: General Questions
  12. GAmbrosio
    Post

    Answered Adhesion issues

    The slicer passes this on, but then there are those "oh, s#13t moments where you see your filament dancing in the air...:) Sent from my iPhone...
    Post by: GAmbrosio, May 21, 2016 in forum: Troubleshooting
  13. GAmbrosio
    Post

    Answered Adhesion issues

    How did that happen? Geof and Mark, On this topic, with the LCD controller how do I set the Z offset? It starts at .50, won't go any lower...
    Post by: GAmbrosio, May 21, 2016 in forum: Troubleshooting
  14. GAmbrosio
    Post

    Is Prototype quality possible?

    Ha, Mark, heck it took me 3 hours to do my Full Graphics LCD, and that's with the cables already plugged into the printer!!! Lol troubleshooting...
    Post by: GAmbrosio, May 21, 2016 in forum: General Questions
  15. GAmbrosio
    Post

    Solved PLA delamination/layers not binding(infill and bottom layers)

    I notice that it is stringing a tad. That usually means it is too hot. 50 mm/s at 190 for PLA usually works for me here at the temperate Northern...
    Post by: GAmbrosio, May 21, 2016 in forum: Troubleshooting