1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by izumi5188

  1. izumi5188
    Post

    Solved Thermal Runaway Hotend

    Sensor wire was ended up breaking. Ordered new one, replaced and made sure leads were good on the motherboard.
    Post by: izumi5188, Jan 23, 2019 in forum: Troubleshooting
  2. izumi5188
    Post

    Solved Thermal Runaway Hotend

    Well woke up to it broken at the connector. I guess I'm ordering more and trying to get the semitec one hooked up as well.
    Post by: izumi5188, Jan 17, 2019 in forum: Troubleshooting
  3. izumi5188
    Post

    Solved Thermal Runaway Hotend

    Okay Mark, I tried giggle it around in the center and in the corner of the printer area where I saw it jumping around before it crashed. I...
    Post by: izumi5188, Jan 17, 2019 in forum: Troubleshooting
  4. izumi5188
    Post

    Solved Thermal Runaway Hotend

    Thanks Mark. I'll try to see if I can get it to jump in the middle of the bed. Would you know as well, If I ever use the semitic thermistors, do...
    Post by: izumi5188, Jan 17, 2019 in forum: Troubleshooting
  5. izumi5188
    Post

    Partial Answer Layer lines on my prints are not even

    So, I see you're still having issues. Are you printing PLA? How old is your filament? And how has it been stored? I've seen this inconsistency...
    Post by: izumi5188, Jan 17, 2019 in forum: Troubleshooting
  6. izumi5188
    Post

    Answered Printer not printing/extruding smooth layers

    I don't know if you solved your problem. But when I've had that clicking on my robo for the exturder, it was actually a lose wire at the stepper...
    Post by: izumi5188, Jan 17, 2019 in forum: Troubleshooting
  7. izumi5188
    Thread

    Solved Thermal Runaway Hotend

    Well back to you fine wizards of the forum. Before I buy a new Thermistor I have a couple of questions. I just replaced this Thermistor in my E3D...
    Thread by: izumi5188, Jan 17, 2019, 7 replies, in forum: Troubleshooting
  8. izumi5188
    Post

    Solved Replacement Print Bed

    I got glass on top on fine. Works great. Heck, get two pieces. If you have a stubborn print where the glue, my case hair spray, doesn't release,...
    Post by: izumi5188, Dec 31, 2018 in forum: General Questions
  9. izumi5188
    Post

    Partial Answer Another clogged hot end question... desperate user

    I was in your shoes several years ago. I got the E3D v6 All Metal from Filasturder per probably Mark's recommendation. They seem to be the better...
    Post by: izumi5188, Dec 12, 2018 in forum: Troubleshooting
  10. izumi5188
    Post

    Solved X-Axis Layer Shift

    Totally forgot to update this. Without replacing the driver and just replacing the belt and bad linear bearings. I have been up and printing. I...
    Post by: izumi5188, Dec 9, 2018 in forum: Troubleshooting
  11. izumi5188
    Post

    Solved X-Axis Layer Shift

    Thanks Mark. Placing the order. Hopefully I get that bearing switched out before the weekend. All depending on when they arrive. I'm probably that...
    Post by: izumi5188, Oct 8, 2018 in forum: Troubleshooting
  12. izumi5188
    Post

    Solved X-Axis Layer Shift

    You also talked about stocking generic ramps. Is this what you are referring too? I converted to a generic board a while back, but all the...
    Post by: izumi5188, Oct 8, 2018 in forum: Troubleshooting
  13. izumi5188
    Post

    Solved X-Axis Layer Shift

    Hey Mark, I haven't had a chance to test swapping the stepper drivers. When I turned my machine over, I found little ball bearings. I've figured...
    Post by: izumi5188, Oct 8, 2018 in forum: Troubleshooting
  14. izumi5188
    Thread

    Solved X-Axis Layer Shift

    I'm away from my machine but this has perplexed me all weekend. Machine is an R1 plus, not sure what version of Marlin I'm running. I am getting...
    Thread by: izumi5188, Oct 1, 2018, 11 replies, in forum: Troubleshooting