1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by jediknight0

  1. jediknight0
    Post

    Answered Enclosure for abs?

    I use aluminum foil and tape to temporarily enclose the printer... assuming the parts I want to print are not too big in the Y axis. But I love...
    Post by: jediknight0, Feb 1, 2017 in forum: General Questions
  2. jediknight0
    Post

    Explosion caused by 3D printer and hairspray kills teenage boy

    I've seen this on several websites today. They usually miss the fact that he was storing flash paper under the printer. Flash paper is used in...
    Post by: jediknight0, Nov 3, 2016 in forum: General Questions
  3. jediknight0
    Post

    Solved smooth rod lengths?

    Yes, it totally makes sense. I'm disappointed that Robo3D support gave me the wrong answer... even after I pressed them on the point.
    Post by: jediknight0, Oct 19, 2016 in forum: General Questions
  4. jediknight0
    Post

    Solved smooth rod lengths?

    Point taken. ;) I looked into installing the eDrawing viewer but the installer said it would need to replace files in use by Simplify3D and 2...
    Post by: jediknight0, Oct 17, 2016 in forum: General Questions
  5. jediknight0
    Post

    Solved smooth rod lengths?

    FYI, I have a support case open with Robo3D. I'm getting confusing answers so far. They say all the rods are the same (X, Y, & Z) at 304mm long....
    Post by: jediknight0, Oct 16, 2016 in forum: General Questions
  6. jediknight0
    Post

    Solved smooth rod lengths?

    Would a standard re-inforced dremel cut-off wheel cut through a standard smooth rod?
    Post by: jediknight0, Oct 14, 2016 in forum: General Questions
  7. jediknight0
    Thread

    Solved smooth rod lengths?

    Does anyone know the length of the smooth rods in a stock R1? My Z axis smooth rods are definitely damaged (probably from before the lead screw...
    Thread by: jediknight0, Oct 14, 2016, 11 replies, in forum: General Questions
  8. jediknight0
    Post

    News about the R2?

    Looks like the kickstarter will be live in a few hours. There's a countdown timer on robo3d.com and it's less than 8 hours to go...
    Post by: jediknight0, Sep 21, 2016 in forum: General Questions
  9. jediknight0
    Post

    News about the R2?

    So tomorrow is the day. I'm surprised (again) that the email list they have been pushing hasn't been sent any early info.
    Post by: jediknight0, Sep 13, 2016 in forum: General Questions
  10. jediknight0
    Thread

    News about the R2?

    Did anyone see this info? https://www.reddit.com/r/3Dprinting/comments/50wqbm/new_robo3d_c2_mini_and_r2_are_going_to_be_up_for/ Sounds like the...
    Thread by: jediknight0, Sep 2, 2016, 109 replies, in forum: General Questions
  11. jediknight0
    Post

    Unresolved Robo3D Z-Axis buzzes and sticks

    It's possible the Z stepper driver needs to be adjusted or replaced as well... but I'd check the firmware first before busting out the screwdriver.
    Post by: jediknight0, Aug 15, 2016 in forum: Troubleshooting
  12. jediknight0
    Post

    Y Axis Bearing Alternative

    Yup. That's exactly what I meant, even if I didn't say it well. ;-)
    Post by: jediknight0, May 25, 2016 in forum: Mods and Upgrades
  13. jediknight0
    Post

    Y Axis Bearing Alternative

    Is one of the bearings on the bearing holders going bad?
    Post by: jediknight0, May 22, 2016 in forum: Mods and Upgrades