1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Jimmy Husain

  1. Jimmy Husain
    Post

    Answered Can anyone reccomend a slicer that is not S3D?

    Just to voice out my point of view. I am also still very new to this hobby. It is expensive, to me. But that did not even make me wanting to...
    Post by: Jimmy Husain, Mar 3, 2016 in forum: General Questions
  2. Jimmy Husain
    Post

    Unanswered Quieter fans for the R1

    @WheresWaldo I didn't know that the PSU fan can also be swapped with a better one. Now you are making me wanting to do just that. Any links you...
    Post by: Jimmy Husain, Feb 28, 2016 in forum: General Questions
  3. Jimmy Husain
    Post

    Unresolved How do I take off the nozzel?

    I am not sure if there is a small wrench given with the Robo printer but for the E3D hotends, they do give you one to remove the nozzle.
    Post by: Jimmy Husain, Feb 26, 2016 in forum: Troubleshooting
  4. Jimmy Husain
    Post

    Unresolved How do I take off the nozzel?

    You will still need to heat it up. 1st time removing it will be abit scary, well to me it was. Then after that you be doing it in no time. That is...
    Post by: Jimmy Husain, Feb 26, 2016 in forum: Troubleshooting
  5. Jimmy Husain
    Post

    Answered Overhang?

    So which will be better? Printing with 0.6 nozzle @ 0.4 mm layers, the V6 or Volcano? I know better can be different to everybody but what do you...
    Post by: Jimmy Husain, Feb 26, 2016 in forum: Troubleshooting
  6. Jimmy Husain
    Post

    Answered Overhang?

    Thanks for the infos guys. I'll try again with 0.2 mm layers later.
    Post by: Jimmy Husain, Feb 25, 2016 in forum: Troubleshooting
  7. Jimmy Husain
    Post

    Answered Overhang?

    Seriously? I did not that with a 0.4 nozzle the max I can go is 0.3 mm layers? I thought after all this while I can print 0.4 mm layers with a...
    Post by: Jimmy Husain, Feb 25, 2016 in forum: Troubleshooting
  8. Jimmy Husain
    Thread

    Answered Overhang?

    I am trying to print this : https://www.youmagine.com/designs/low-poly-retro-characters I printed the Mario model & below is what I get....
    Thread by: Jimmy Husain, Feb 25, 2016, 8 replies, in forum: Troubleshooting
  9. Jimmy Husain
    Post

    Web enabled Robo3d using Raspberry Pi and Octoprint

    I can't upload to the SD card. It is greyed out. Clicking on the "Initialise SD Card" is not helping too.
    Post by: Jimmy Husain, Feb 23, 2016 in forum: Mods and Upgrades
  10. Jimmy Husain
    Post

    Web enabled Robo3d using Raspberry Pi and Octoprint

    Speaking of which, do I need to make a Printer Profile for my Robo? Or is it not needed?
    Post by: Jimmy Husain, Feb 15, 2016 in forum: Mods and Upgrades
  11. Jimmy Husain
    Post

    Web enabled Robo3d using Raspberry Pi and Octoprint

    Finally this whole mod is up & running today. Days of inserting & removing the sd card are things in the past.
    Post by: Jimmy Husain, Feb 15, 2016 in forum: Mods and Upgrades
  12. Jimmy Husain
    Post

    NinjaFlex filament

    ^^Thanks. Printing with this thing is a pain but fun.
    Post by: Jimmy Husain, Feb 10, 2016 in forum: Printing Filament
  13. Jimmy Husain
    Post

    NinjaFlex filament

    Just to check, do I need the fan to be on with NinjaFlex?
    Post by: Jimmy Husain, Feb 9, 2016 in forum: Printing Filament
  14. Jimmy Husain
    Post

    Smaller nozzel use?

    So do I need to change my speed when going with smaller nozzle? Like right now I am on 60mm/s with 0.4 nozzle. So if going to 0.3 or 0.2 should...
    Post by: Jimmy Husain, Feb 7, 2016 in forum: General Questions