1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by kapu007

  1. kapu007
    Post

    Unresolved robo r1 plus turns off

    thank you for the info. I removed the old daughter cards and install it on the new ramp and same issue. I've no experience in using the volt...
    Post by: kapu007, Nov 7, 2016 in forum: Troubleshooting
  2. kapu007
    Post

    Unresolved robo r1 plus turns off

    How do I tune it? I'm really new at this kind of stuff.
    Post by: kapu007, Nov 7, 2016 in forum: Troubleshooting
  3. kapu007
    Post

    Unresolved robo r1 plus turns off

    Yes, I did replace the arduino.
    Post by: kapu007, Nov 7, 2016 in forum: Troubleshooting
  4. kapu007
    Post

    Unresolved robo r1 plus turns off

    [MEDIA]
    Post by: kapu007, Nov 7, 2016 in forum: Troubleshooting
  5. kapu007
    Post

    How to Update and Edit Robo firmware with Arduino

    I change out my robo 3d r1 plus, psu, controller board and the hotend due to the printer turning off when starting to print. Now it will go crazy...
    Post by: kapu007, Nov 7, 2016 in forum: Software
  6. kapu007
    Post

    Unresolved robo r1 plus turns off

    I check it again and the wire was loose. Now I can get the temp to 185. I started a print but the hotend and seems like the robo r1 plus unit...
    Post by: kapu007, Nov 6, 2016 in forum: Troubleshooting
  7. kapu007
    Post

    Unresolved robo r1 plus turns off

    Hey Mark, Well things really not working out fixing my robo r1 plus. after changing out the board, psu and hotend. robo can't level anymore nor...
    Post by: kapu007, Nov 6, 2016 in forum: Troubleshooting
  8. kapu007
    Post

    Unresolved robo r1 plus turns off

    I replaced the board and now the extruder will not get over 25.4. selected preheat and waited for 15 mins and no change. Any ideas?
    Post by: kapu007, Nov 4, 2016 in forum: Troubleshooting
  9. kapu007
    Post

    Unresolved robo r1 plus turns off

    I bought a thermistor and replaced it. still yet didn't work. Found out the board was the issue. I got a replacement in and when I change it out,...
    Post by: kapu007, Nov 4, 2016 in forum: Troubleshooting
  10. kapu007
    Post

    Unresolved robo r1 plus turns off

    yes the fan is blowing on the board. I guess the polyfuser is bad on the board. I'm new to this....thanks
    Post by: kapu007, Oct 20, 2016 in forum: Troubleshooting
  11. kapu007
    Post

    Unresolved robo r1 plus turns off

    I replaced the thermistor with a new one and still having the same problem. If I heat it to 185 the led light white on the right inside will start...
    Post by: kapu007, Oct 19, 2016 in forum: Troubleshooting
  12. kapu007
    Post

    Unresolved robo r1 plus turns off

    thank you for your help
    Post by: kapu007, Oct 9, 2016 in forum: Troubleshooting
  13. kapu007
    Post

    Unresolved robo r1 plus turns off

    working with robo now and hope they'll send me one.
    Post by: kapu007, Oct 9, 2016 in forum: Troubleshooting
  14. kapu007
    Post

    Unresolved robo r1 plus turns off

    thank you for the instruction.
    Post by: kapu007, Oct 9, 2016 in forum: Troubleshooting
  15. kapu007
    Post

    Unresolved robo r1 plus turns off

    thank you and I have an R1 plus, is there a instruction on how to do this? I'm new at this with hardware related stuff..thank you
    Post by: kapu007, Oct 8, 2016 in forum: Troubleshooting