1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Lary

  1. Lary
    Post

    Solved Bed temp shows wrong temp between 66 and 67 degrees

    Well got the new Arduino from Robo and that was it!!! The board itself was the problem.
    Post by: Lary, Jun 19, 2017 in forum: Troubleshooting
  2. Lary
    Post

    Solved Bed temp shows wrong temp between 66 and 67 degrees

    Can you use another Arduino Mega 2560 to power the Ramps board and the Robo3dR1+ or are there some issues? I only have been using the USB part of...
    Post by: Lary, Jun 10, 2017 in forum: Troubleshooting
  3. Lary
    Post

    Solved Bed temp shows wrong temp between 66 and 67 degrees

    Well now it is even better. I took another Ramps Board and Arduino connected it and the temps are correct. I took the Ramps and put it on the...
    Post by: Lary, Jun 10, 2017 in forum: Troubleshooting
  4. Lary
    Post

    Solved Bed temp shows wrong temp between 66 and 67 degrees

    Well thanks to the great response from Robo 3D I have a new board but guess what...The temperature is still the same 67-68 degrees. No...
    Post by: Lary, Jun 10, 2017 in forum: Troubleshooting
  5. Lary
    Post

    Solved Bed temp shows wrong temp between 66 and 67 degrees

    Thanks Mark, I shorted the pins and they changed does that change your response? I'm thinking it is a bad board myself but I would think it...
    Post by: Lary, Jun 3, 2017 in forum: Troubleshooting
  6. Lary
    Thread

    Solved Bed temp shows wrong temp between 66 and 67 degrees

    I'm really stumped. The temperature in my room is 24 degrees. I have a Robo 3Dr1+ and had to change the boards. Now the temp for the extruder...
    Thread by: Lary, Jun 3, 2017, 12 replies, in forum: Troubleshooting
  7. Lary
    Post

    Issue with drop of filament at beginning of print

    Starts to print it pushes/creates a very tiny blob but big enough to change the direction of flow. Just a little drop then it flows correctly and...
    Post by: Lary, Jan 21, 2017 in forum: Mods and Upgrades
  8. Lary
    Thread

    Issue with drop of filament at beginning of print

    No matter what I try it seems with my new E3D that it always wants to start with a little drop of filament when it starts printing. I have tried...
    Thread by: Lary, Jan 21, 2017, 4 replies, in forum: Mods and Upgrades
  9. Lary
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Yep. Also this particular SD card works with the XXL screen with no problems.
    Post by: Lary, Jan 20, 2017 in forum: Mods and Upgrades
  10. Lary
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Guess I must have a defective LCD screen. I am using that version. Weird how it detects the SD card but can't detect the files though.
    Post by: Lary, Jan 19, 2017 in forum: Mods and Upgrades
  11. Lary
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    When the Robo 3D r1+ boots up the screen says: RoboR1 Plus ABL ready. That is the correct one? It still has the same issue. It looks like you...
    Post by: Lary, Jan 19, 2017 in forum: Mods and Upgrades
  12. Lary
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    The one that you supplied. Maybe I should reload yours again and see if that fixes it. They were in your post of December 6th since that is the...
    Post by: Lary, Jan 19, 2017 in forum: Mods and Upgrades
  13. Lary
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Didn't work either.
    Post by: Lary, Jan 19, 2017 in forum: Mods and Upgrades