1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Matt Gorski

  1. Matt Gorski
    Post

    Solved Z axis only moves up won't move down

    Fixed :)
    Post by: Matt Gorski, Jan 28, 2017 in forum: Troubleshooting
  2. Matt Gorski
    Post

    Solved Z axis only moves up won't move down

    I think I fixed it! Running a calibration circle quick but it was the positioning. I had to push the rod a bit and it came down on the switch :)
    Post by: Matt Gorski, Jan 28, 2017 in forum: Troubleshooting
  3. Matt Gorski
    Post

    Solved Z axis only moves up won't move down

    From the video it looks to be improper positioning.
    Post by: Matt Gorski, Jan 28, 2017 in forum: Troubleshooting
  4. Matt Gorski
    Post

    Solved Z axis only moves up won't move down

    I read through all of those posts. Tried reflashing firmware and re-aligned the switches. See pic. Still won't move down so I assume it a bad...
    Post by: Matt Gorski, Jan 28, 2017 in forum: Troubleshooting
  5. Matt Gorski
    Thread

    Solved Z axis only moves up won't move down

    Okay so I have gone through all the threads discussing this issue and I cant figure out the issue. I moved my z axis up too far and now I had to...
    Thread by: Matt Gorski, Jan 28, 2017, 8 replies, in forum: Troubleshooting
  6. Matt Gorski
    Post

    Unresolved Wrinkles in layers

    So what material would you all recommend for an electronics/mini pc enclosure?
    Post by: Matt Gorski, Jan 14, 2017 in forum: Troubleshooting
  7. Matt Gorski
    Post

    Unresolved Wrinkles in layers

    Lower temp huh? Would not have thought that would be the culprit. I'll try some lower temps and report back. Thank you kindly for the Saturday...
    Post by: Matt Gorski, Jan 14, 2017 in forum: Troubleshooting
  8. Matt Gorski
    Thread

    Unresolved Wrinkles in layers

    Just curious why this seems to happen sporadically. I've adjusted my flow, Z height, speed ECT and I still get waves/wrinkles. I've read a few...
    Thread by: Matt Gorski, Jan 14, 2017, 11 replies, in forum: Troubleshooting
  9. Matt Gorski
    Post

    Arduino/Ramps issues

    It was a $5 programmer I bought just to see if it revived the stock Mega 2560. No big deal im not expecting to revive it and I do assume it was...
    Post by: Matt Gorski, Dec 12, 2016 in forum: Troubleshooting
  10. Matt Gorski
    Post

    Arduino/Ramps issues

    Okay another update to this thread. To further my experience I ordered a programmer to try and burn the bootloader on my stock Robo Arduino....
    Post by: Matt Gorski, Dec 12, 2016 in forum: Troubleshooting
  11. Matt Gorski
    Post

    Arduino/Ramps issues

    Okay close call all I had to do was uninstall the RAMPS driver and let it use the default USB serial driver. Now heat bed extruder and all...
    Post by: Matt Gorski, Dec 9, 2016 in forum: Troubleshooting
  12. Matt Gorski
    Post

    Arduino/Ramps issues

    I'm getting nervous now....
    Post by: Matt Gorski, Dec 9, 2016 in forum: Troubleshooting
  13. Matt Gorski
    Post

    Arduino/Ramps issues

    Okay I can't seem to connect again after installing RAMPS and I was very very very careful this time. Programmed fine comes up in device manager...
    Post by: Matt Gorski, Dec 9, 2016 in forum: Troubleshooting