1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Morant

  1. Morant
    Post

    Somewhat New to 3D Printing Have Some Basic Questions

    Yes, it is possible to use PEI on an unheated bed, especially for PLA. PEI offers excellent adhesion for PLA even without heat. However, its...
    Post by: Morant, May 21, 2025 in forum: General Questions
  2. Morant
    Post

    Answered Is this filament good ?

    I just realized this is a post from 2018—probably no one’s going to reply anymore. That said, the PLA and PETG I usually use are pretty standard...
    Post by: Morant, Apr 30, 2025 in forum: General Questions
  3. Morant
    Post

    Change filament without parking ?

    You want filament runout detection, but you don’t want the printer to park the nozzle during a change. Right？This might require trying to edit the...
    Post by: Morant, Apr 30, 2025 in forum: General Questions
  4. Morant
    Post

    TPU settings

    TPU is very flexible, so print slowly—start around 20-30mm/s.
    Post by: Morant, Apr 1, 2025 in forum: Filament
  5. Morant
    Post

    About materials -

    The Heat Deflection Temperature (HDT) of standard PETG is 70°C, which is close to the upper limit of dishwasher high-temperature cycles (60-70°C)....
    Post by: Morant, Mar 30, 2025 in forum: General Questions
  6. Morant
    Post

    Best Wood and conductive filaments?

    Kingroon Wood PLA contains wood particles (approximately 20%-40%), and sanding can reveal a natural wood-like grain texture. Its interlayer...
    Post by: Morant, Mar 30, 2025 in forum: General Questions
  7. Morant
    Post

    3D Solutech Glow In Dark 3D Printer PLA Filament

    I think this glow-in-the-dark PLA is quite interesting—the glowing effect is distinct, and the printing performance is good. For the settings, I...
    Post by: Morant, Mar 25, 2025 in forum: Filament
  8. Morant
    Post

    Question about PETG

    Could the "rainbow PETG" you're referring to be due to excessive humidity? I recommend drying the filament in a filament dryer (for example, at...
    Post by: Morant, Mar 25, 2025 in forum: Filament
  9. Morant
    Post

    3mm filament?

    Remember to slow down the print speed. There's no problem printing with a 3mm filament.
    Post by: Morant, Mar 6, 2025 in forum: Printing Filament
  10. Morant
    Post

    Filament and humidity

    I suggest you get a filament dryer, but sometimes I forget to use it and just put it in the oven to bake for a while.
    Post by: Morant, Mar 6, 2025 in forum: Filament
  11. Morant
    Post

    How to print flexible filament?

    Make sure the path of the filament from the spool to the extruder is as short and smooth as possible, avoiding sharp turns or friction.
    Post by: Morant, Mar 6, 2025 in forum: Filament
  12. Morant
    Post

    Just yammering - Filament Color and Z Offset

    White filament can also be combined with print bed leveling and extrusion calibration to achieve the best results.
    Post by: Morant, Mar 6, 2025 in forum: Filament
  13. Morant
    Thread

    Do you think the filament dryer is necessary 3d printing tool？

    I ask my friends and the Chatgpt, and they all think the filament dryer is a necessary 3d printing tool. I think the two advantages are important...
    Thread by: Morant, Dec 4, 2024, 2 replies, in forum: General Questions
  14. Morant
    Post

    Supposedly save up to 99% home printing with Ninjaflex

    I just went to search for relevant information.compared to ABS filament, Ninjaflex has 20% better abrasion resistance, and 68% better than PLA....
    Post by: Morant, Dec 4, 2024 in forum: Off Topic