1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Oisin

  1. Oisin
    Post

    Partial Answer Extreme stringing control.

    I can pick up some ColourFab Bamboo Woodfill here in Ireland for 40 euros. I'll do so and compare the results.
    Post by: Oisin, Jun 26, 2017 in forum: Troubleshooting
  2. Oisin
    Post

    Partial Answer Extreme stringing control.

    I got the 0.25 because I usually print at 50 - 100 micron. 50 micron with Woodfill looks incredible. The layer lines are completely invisible. 100...
    Post by: Oisin, Jun 26, 2017 in forum: Troubleshooting
  3. Oisin
    Post

    Partial Answer Extreme stringing control.

    Thanks very much for all of the advice, Ryan. I've attached my FFF. I'll try that model. Thanks for linking it! I have an oiler but I haven't...
    Post by: Oisin, Jun 26, 2017 in forum: Troubleshooting
  4. Oisin
    Post

    Partial Answer Extreme stringing control.

    Here's another attempt. This one was printed with no coasting or wiping. Retraction was 5mm at 90mm/s and 0.6mm lift. It was printed all the way...
    Post by: Oisin, Jun 26, 2017 in forum: Troubleshooting
  5. Oisin
    Post

    Partial Answer Extreme stringing control.

    I decided to print the model from this video: [MEDIA] It has six different sections that you can apply different processes to. If you look at...
    Post by: Oisin, Jun 26, 2017 in forum: Troubleshooting
  6. Oisin
    Post

    Partial Answer Extreme stringing control.

    Lower it from 175? And I'll try knocking it from 30 to 15mm/s.
    Post by: Oisin, Jun 24, 2017 in forum: Troubleshooting
  7. Oisin
    Thread

    Partial Answer Extreme stringing control.

    Hi guys. I've recently started using Woodfill. It's got the best surface quality I've ever seen, so I definitely want to keep using it. The issue...
    Thread by: Oisin, Jun 23, 2017, 16 replies, in forum: Troubleshooting
  8. Oisin
    Post

    Unresolved Defects on print surface.

    I've not had any regular PLA, KMT. I've only run PETG and the Woodfill through it and had the same effect with both despite pretty different...
    Post by: Oisin, May 25, 2017 in forum: Troubleshooting
  9. Oisin
    Post

    Unresolved Defects on print surface.

    And it doesn't occur with other filaments? Because the exact same thing happens to me with PETG, so I was thinking it was a printer thing.
    Post by: Oisin, May 25, 2017 in forum: Troubleshooting
  10. Oisin
    Post

    Unresolved Defects on print surface.

    It's an improvement but still something that shouldn't be occurring. I've yet to try some fresh filament so we'll see what difference that makes,...
    Post by: Oisin, May 25, 2017 in forum: Troubleshooting
  11. Oisin
    Post

    Unresolved Defects on print surface.

    The below images are of the print after changing retraction from 3.6 to 6mm, temperature from 195C to 180C and that's all. Speed was 40mm/s and...
    Post by: Oisin, May 24, 2017 in forum: Troubleshooting
  12. Oisin
    Post

    Unresolved Defects on print surface.

    I'll definitely try your suggestions once this print finishes. I'll print a second one with your settings to compare. I love the surface finish on...
    Post by: Oisin, May 23, 2017 in forum: Troubleshooting
  13. Oisin
    Post

    Unresolved Defects on print surface.

    The nozzle diameter 0.25mm, or it was when I bought it. It has probably seen less than 200 hours of printing. I feel like that's not a lot. I'll...
    Post by: Oisin, May 23, 2017 in forum: Troubleshooting
  14. Oisin
    Thread

    Unresolved Defects on print surface.

    Hi guys. I'm having some strange little pellets be deposited on my print as per my images. I'm wondering if anyone could help identify it. I'm...
    Thread by: Oisin, May 23, 2017, 15 replies, in forum: Troubleshooting