1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Paul Pangrazzi

  1. Paul Pangrazzi
    Post

    PID calibration

    It is indeed! Thank you for the big assist... I've grabbed the image and already made copies on dedicated SD card backups. - Now on to replacing...
    Post by: Paul Pangrazzi, Apr 12, 2020 in forum: Troubleshooting
  2. Paul Pangrazzi
    Post

    Solved OK to use Stock Arduino Mega 2560 R3 in R1+?

    I'm all in now... but a bit over my head. Since I'm going to need to source an additional RAMPS 1.4 board for my R2, I'm considering going with...
    Post by: Paul Pangrazzi, Apr 6, 2020 in forum: Troubleshooting
  3. Paul Pangrazzi
    Post

    Solved OK to use Stock Arduino Mega 2560 R3 in R1+?

    Thank you. Will do.
    Post by: Paul Pangrazzi, Apr 6, 2020 in forum: Troubleshooting
  4. Paul Pangrazzi
    Post

    Solved OK to use Stock Arduino Mega 2560 R3 in R1+?

    @mark tomlinson I've got a new Arduino Mega 2560 in hand to try and fix some temp issues (hotend won't heat more than 165C and bed reports 40C...
    Post by: Paul Pangrazzi, Apr 6, 2020 in forum: Troubleshooting
  5. Paul Pangrazzi
    Post

    Z-Offset Wizard stuck at step 1 of 4

    Closing out my original post... I have a new issue regarding temps, but after using the updated R2 FAQ (links to new 2.0.0-r2.6 image) and...
    Post by: Paul Pangrazzi, Apr 1, 2020 in forum: Troubleshooting
  6. Paul Pangrazzi
    Post

    PID calibration

    I appreciate your help, but I've read and reread your excellent FAQ and it appears the only R2 image is a 1.5.0-r.2.0 version:...
    Post by: Paul Pangrazzi, Mar 30, 2020 in forum: Troubleshooting
  7. Paul Pangrazzi
    Post

    PID calibration

    Wow! Ok then. Good to know. What is the proper method for updating RoboOS from the 1.50 image to 2.0.0-r26?
    Post by: Paul Pangrazzi, Mar 30, 2020 in forum: Troubleshooting
  8. Paul Pangrazzi
    Post

    PID calibration

    Ok, I'll reinstall the SD card software again from the image at:...
    Post by: Paul Pangrazzi, Mar 30, 2020 in forum: Troubleshooting
  9. Paul Pangrazzi
    Post

    PID calibration

    Hm. I don't have a PID Tuning Wizard on my R2. I'm running 2.0.0-r2.6. Anyone know why it doesn't appear?
    Post by: Paul Pangrazzi, Mar 30, 2020 in forum: Troubleshooting
  10. Paul Pangrazzi
    Post

    Z-Offset Wizard stuck at step 1 of 4

    The diagram was crystal clear; very helpful. Now I'm trying to print your example .stl and I can't get the hotend to heat up past 150C. *Long look...
    Post by: Paul Pangrazzi, Mar 30, 2020 in forum: Troubleshooting
  11. Paul Pangrazzi
    Post

    Z-Offset Wizard stuck at step 1 of 4

    That's good news! I've already removed the assembly from the printer; I'll clean it up later and perform the fix.
    Post by: Paul Pangrazzi, Mar 30, 2020 in forum: Troubleshooting
  12. Paul Pangrazzi
    Post

    Z-Offset Wizard stuck at step 1 of 4

    I knew I should have knocked on wood. The hot end failed on the test print; plastic is oozing out of the top of the heater block and everything is...
    Post by: Paul Pangrazzi, Mar 30, 2020 in forum: Troubleshooting
  13. Paul Pangrazzi
    Post

    Z-Offset Wizard stuck at step 1 of 4

    Hello @mark tomlinson , and thank you for the speedy reply. I'll do as you say and report back... while remaining curious about why the Wizard is...
    Post by: Paul Pangrazzi, Mar 30, 2020 in forum: Troubleshooting
  14. Paul Pangrazzi
    Post

    Z-Offset Wizard stuck at step 1 of 4

    I'm having the same issue as the OP. I can't seem to run the z offset wizard; it's stuck on step 1 of 4. Quick history: I've just removed the...
    Post by: Paul Pangrazzi, Mar 30, 2020 in forum: Troubleshooting
  15. Paul Pangrazzi
    Post

    Robo R2: Filament Detection Falsely Being Activated (is anyone else having this issue?)

    Argh. It was totally my fault... I had the filament coming off the spool and going through the left side hole (when facing the rear.) When I fed...
    Post by: Paul Pangrazzi, Jun 16, 2017 in forum: Troubleshooting