1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Perry

  1. Perry
    Post

    Solved Brand new to 3D printing - RoBo 3D R1+ - Multiple issues

    Thanks everyone for your help. I did not need to work on the extruder accuracy this weekend because I believe I may have found what the issue...
    Post by: Perry, Dec 19, 2016 in forum: Troubleshooting
  2. Perry
    Post

    Solved Brand new to 3D printing - RoBo 3D R1+ - Multiple issues

    I'm using the V2 firmware I downloaded from Robo's website. Why would there be an issue with their firmware?
    Post by: Perry, Dec 15, 2016 in forum: Troubleshooting
  3. Perry
    Post

    Solved Brand new to 3D printing - RoBo 3D R1+ - Multiple issues

    Thanks guys, for your responses. Its strange that these settings aren't easier to adjust than they are. Looks like I'll have to check the...
    Post by: Perry, Dec 15, 2016 in forum: Troubleshooting
  4. Perry
    Post

    Solved Brand new to 3D printing - RoBo 3D R1+ - Multiple issues

    Thanks everybody for your software notes. I'll probably be trying Cura in the near future, but I decided to stick with MatterControl for now...
    Post by: Perry, Dec 15, 2016 in forum: Troubleshooting
  5. Perry
    Post

    Solved Brand new to 3D printing - RoBo 3D R1+ - Multiple issues

    Quick question, what (free) software do you recommend? I've been looking at Cura and it seems like it may be a little more user-friendly than...
    Post by: Perry, Dec 13, 2016 in forum: Troubleshooting
  6. Perry
    Post

    Solved Brand new to 3D printing - RoBo 3D R1+ - Multiple issues

    Thanks, I'll keep reducing the Z axis until I get a good skirt like that one. Appreciate the tips!
    Post by: Perry, Dec 13, 2016 in forum: Troubleshooting
  7. Perry
    Post

    Solved Brand new to 3D printing - RoBo 3D R1+ - Multiple issues

    @mark tomlinson OK, so after speaking with a very patient Robo3D tech last night, I may be ordering a new stepper motor and wiring harness for...
    Post by: Perry, Dec 13, 2016 in forum: Troubleshooting
  8. Perry
    Post

    Solved Brand new to 3D printing - RoBo 3D R1+ - Multiple issues

    @mark tomlinson @Rigmarol I think I might have actually gotten it to work! See in-progress pic, attached. The Z-axis offset was set to 0, so i...
    Post by: Perry, Dec 9, 2016 in forum: Troubleshooting
  9. Perry
    Post

    Solved Brand new to 3D printing - RoBo 3D R1+ - Multiple issues

    Thank you, I'll give it a look. I'm fairly certain it was running, because I noticed the fan making noise.
    Post by: Perry, Dec 9, 2016 in forum: Troubleshooting
  10. Perry
    Post

    Solved Brand new to 3D printing - RoBo 3D R1+ - Multiple issues

    Thank you, I'll give it a try tonight.
    Post by: Perry, Dec 9, 2016 in forum: Troubleshooting
  11. Perry
    Post

    Solved Brand new to 3D printing - RoBo 3D R1+ - Multiple issues

    I think I understand, but I watched a Youtube video of a guy printing the circle using the same software and it didn't make any straight lines, it...
    Post by: Perry, Dec 9, 2016 in forum: Troubleshooting
  12. Perry
    Post

    Solved Brand new to 3D printing - RoBo 3D R1+ - Multiple issues

    Thanks, yes I've seen that it'll touch points on the plate, but it actually started printing straight-ish lines (not exactly straight because of...
    Post by: Perry, Dec 9, 2016 in forum: Troubleshooting
  13. Perry
    Post

    Solved Brand new to 3D printing - RoBo 3D R1+ - Multiple issues

    Thanks for the quick reply @mark tomlinson. I'll definitely check again under the plate, but there did not appear to be anything getting in the...
    Post by: Perry, Dec 9, 2016 in forum: Troubleshooting
  14. Perry
    Thread

    Solved Brand new to 3D printing - RoBo 3D R1+ - Multiple issues

    Hi, I am completely new to 3D printing, so please bear with me. I have tried to read up on these issues, but haven't had much luck finding...
    Thread by: Perry, Dec 9, 2016, 30 replies, in forum: Troubleshooting