1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Suberman

  1. Suberman
    Post

    Unanswered Robo 3d R1 Plus

    This is my problem. Continuity is working. Any other advise? [MEDIA]
    Post by: Suberman, Jan 14, 2018 in forum: Troubleshooting
  2. Suberman
    Post

    Unanswered Robo 3d R1 Plus

    This is the switch that would be showing closed right?
    Post by: Suberman, Jan 14, 2018 in forum: Troubleshooting
  3. Suberman
    Post

    Unanswered Robo 3d R1 Plus

    It's possible but not likely. Why is it if i'm jogging the x+ or x- it works great only when i'm homing it before a print it goes the wrong way?...
    Post by: Suberman, Jan 14, 2018 in forum: Troubleshooting
  4. Suberman
    Thread

    Unanswered Robo 3d R1 Plus

    How do you know if you need to replace the driver stepper motor on the arduino board vs the servo motor? I have 2 different problems. I'm moving...
    Thread by: Suberman, Jan 14, 2018, 6 replies, in forum: Troubleshooting
  5. Suberman
    Post

    Unanswered Help with Matter Control

    I feel like i'm getting closer however i'm not sure what to do to get this right.
    Post by: Suberman, Jan 9, 2018 in forum: Troubleshooting
  6. Suberman
    Post

    Unanswered Help with Matter Control

    What program do you use to print?
    Post by: Suberman, Jan 9, 2018 in forum: Troubleshooting
  7. Suberman
    Post

    Unanswered Help with Matter Control

    After several prints and changes I think my best print is a layer height .25 Temp 205 & 210. I never could get the top of the pyramid to come out...
    Post by: Suberman, Jan 9, 2018 in forum: Troubleshooting
  8. Suberman
    Post

    Unanswered Help with Matter Control

    I will try different temperature setting. I will also move my layer height to .25. Its currently at .4. On the label reads diameter 1.75mm...
    Post by: Suberman, Jan 9, 2018 in forum: Troubleshooting
  9. Suberman
    Post

    Unanswered Help with Matter Control

    My tall prints are still coming out with no detail and now its stringy. How can I get a more detailed print when I print something tall? I'm...
    Post by: Suberman, Jan 8, 2018 in forum: Troubleshooting
  10. Suberman
    Post

    Unanswered Help with Matter Control

    AMAZING!!! THANK YOU!! Its not perfect but its a better print at half the time. You just save half of my printer life :). Can you explain the...
    Post by: Suberman, Jan 8, 2018 in forum: Troubleshooting
  11. Suberman
    Post

    Unanswered Help with Matter Control

    I'm not sure I understand. If you look at the screenshot it reads for layer height "The height of each layer of the print, except the first. A...
    Post by: Suberman, Jan 8, 2018 in forum: Troubleshooting
  12. Suberman
    Post

    Unanswered Help with Matter Control

    This is a screenshot just in case you don't understand.
    Post by: Suberman, Jan 8, 2018 in forum: Troubleshooting
  13. Suberman
    Post

    Unanswered Help with Matter Control

    What should my setting be? I like to use Matter Control 1.7 software. I have the infill set to .40 (Fill Density) infill type in set to grid....
    Post by: Suberman, Jan 8, 2018 in forum: Troubleshooting
  14. Suberman
    Post

    Unanswered Help with Matter Control

    why is it when I change the EEProm i'm able to print? I'm having another problem that I would like some help with. I'm changing my fill density...
    Post by: Suberman, Jan 8, 2018 in forum: Troubleshooting