1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by supercazzola

  1. supercazzola
    Post

    what is the size of the set screw for the Filament drive gear

    worked like a charm. thanks for the advice.
    Post by: supercazzola, Dec 11, 2023 in forum: Troubleshooting
  2. supercazzola
    Thread

    guide to replacing Carriage Bracket and bushing sleeves on the R2?

    Is there a step by step guide to replacing Carriage Bracket and bushing sleeves on the R2? I just got some parts in from partsbuild.com, so...
    Thread by: supercazzola, Dec 11, 2023, 2 replies, in forum: Troubleshooting
  3. supercazzola
    Post

    what is the size of the set screw for the Filament drive gear

    tried it. no joy. So time to drill...
    Post by: supercazzola, Dec 11, 2023 in forum: Troubleshooting
  4. supercazzola
    Post

    what is the size of the set screw for the Filament drive gear

    I’ll be glad to, but if the set screw’s 1.5 mm hole is no longer 1.5, how would having their Allen wrench help ?
    Post by: supercazzola, Dec 7, 2023 in forum: Troubleshooting
  5. supercazzola
    Thread

    what is the size of the set screw for the Filament drive gear

    the hex is stripped and I can not remove the Filament drive gear set screw. Before I drill it out, I'd like to know what the specs are. I see that...
    Thread by: supercazzola, Dec 3, 2023, 6 replies, in forum: Troubleshooting
  6. supercazzola
    Post

    Leveling the R2 Print Bed

    thanks. I may just stick with the machine how it is until I decide if I want another model. I really dislike the hex head, and I just am at a...
    Post by: supercazzola, May 21, 2023 in forum: Troubleshooting
  7. supercazzola
    Post

    Leveling the R2 Print Bed

    Thanks Lance. Your post says not to do it with the original R2 boards, which I still have. I'm sort of thinking I may sell my R2. It still runs...
    Post by: supercazzola, May 21, 2023 in forum: Troubleshooting
  8. supercazzola
    Post

    Leveling the R2 Print Bed

    What I find is my bed is not flat. So the center area where 90% of my prints are printed is perfect, but the outer edges are lower, and the print...
    Post by: supercazzola, May 21, 2023 in forum: Troubleshooting
  9. supercazzola
    Post

    onboard Raspberry Pi is slow and keeps disconnecting from my wifi

    What I was trying to say was, in the factory SD card, I used to view the EEPROM Settings, and see the z-offset. On the vanilla Octoprint, I assume...
    Post by: supercazzola, Feb 12, 2023 in forum: Troubleshooting
  10. supercazzola
    Post

    onboard Raspberry Pi is slow and keeps disconnecting from my wifi

    @mark tomlinson with the default octopi, how do you do any sort of calculation of z-offset after you replace nozzle, for example?
    Post by: supercazzola, Feb 12, 2023 in forum: Troubleshooting
  11. supercazzola
    Post

    onboard Raspberry Pi is slow and keeps disconnecting from my wifi

    Thanks. It’s been a fun ride to learn how to do it. I’m very appreciative of you sharing your card’s image, but, I will probably stick with the...
    Post by: supercazzola, Jan 14, 2023 in forum: Troubleshooting
  12. supercazzola
    Post

    onboard Raspberry Pi is slow and keeps disconnecting from my wifi

    Thanks. Once I get done, I’ll clean up the writeup and make a post that could be a sticky and be “how to run new version of Octoprint and use LCD”...
    Post by: supercazzola, Jan 12, 2023 in forum: Troubleshooting