1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Toro1966

  1. Toro1966
    Post

    Anyone have experience with Palette+ ?

    So I just bought, returned, and today rebought the Palette +. I returned the first one because it arrived damaged I believe. I say I believe...
    Post by: Toro1966, Nov 14, 2017 in forum: General Questions
  2. Toro1966
    Post

    Issues with overhang/underside of prints.

    I know you've tried this with multiple models, but try something other than the viper. I get great prints and I have never been able to print that...
    Post by: Toro1966, Aug 6, 2017 in forum: Troubleshooting
  3. Toro1966
    Post

    Answered Supports not staying stuck to bed, ruining prints

    4mm Mark - been using the same ones for 6 months with no issue. Haven't had to use a raft before. Not sure why this just started.
    Post by: Toro1966, Feb 1, 2017 in forum: Troubleshooting
  4. Toro1966
    Thread

    Answered Supports not staying stuck to bed, ruining prints

    Hey guys, just recently started having this issue and I print a lot. Using S3D and hair spray, with MeltInk PLA. temps are about 55/192....
    Thread by: Toro1966, Feb 1, 2017, 4 replies, in forum: Troubleshooting
  5. Toro1966
    Post

    E3D v6 Information, Installation Guides, and Review

    Check to make sure the correct port is selected. Also check to make sure you don't have any other programs open using the printer (S3D, MC, etc)
    Post by: Toro1966, Jan 28, 2017 in forum: Mods and Upgrades
  6. Toro1966
    Post

    Solved Extruder Calibration Issue

    What's amazing is if I bump it up to 195 it extrudes perfectly. I've already ran autotune as well....
    Post by: Toro1966, Jan 23, 2017 in forum: Troubleshooting
  7. Toro1966
    Post

    Solved Extruder Calibration Issue

    Thanks Waldo - we must have posted at the same time. Just saw your response. Appreciate it.
    Post by: Toro1966, Jan 23, 2017 in forum: Troubleshooting
  8. Toro1966
    Post

    Solved Extruder Calibration Issue

    That's unfortunately what I was thinking. Thanks for the quick help.
    Post by: Toro1966, Jan 23, 2017 in forum: Troubleshooting
  9. Toro1966
    Post

    Solved Extruder Calibration Issue

    Thanks Mark - any thoughts on corrective measures? Just print at a higher temp? I can do that of course, I just get concerned about stringing....
    Post by: Toro1966, Jan 23, 2017 in forum: Troubleshooting
  10. Toro1966
    Post

    Solved Extruder Calibration Issue

    I even can see on the LCD what value is in the printer.
    Post by: Toro1966, Jan 23, 2017 in forum: Troubleshooting
  11. Toro1966
    Post

    Solved Extruder Calibration Issue

    Yup
    Post by: Toro1966, Jan 23, 2017 in forum: Troubleshooting
  12. Toro1966
    Thread

    Solved Extruder Calibration Issue

    Hey guys - went to recalibrate the extruder today and I'm having some issues. No matter what I set the esteps to, I am still underextruding (85...
    Thread by: Toro1966, Jan 23, 2017, 12 replies, in forum: Troubleshooting
  13. Toro1966
    Post

    E3DV6 Hotend Installation Guide on Robo R1+

    Sorry. Meant to fix that link. Here you go. These should work. I'll get an updated version in the next week or so....
    Post by: Toro1966, Jan 15, 2017 in forum: Mods and Upgrades