1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by VBUZZ

  1. VBUZZ
    Post

    Partial Answer Extruder Stuttering In Place

    i dont know if you checked or not but my extruder started doing that and i found out it was one of the wires on the plug going to that servo had a...
    Post by: VBUZZ, Mar 30, 2017 in forum: Troubleshooting
  2. VBUZZ
    Thread

    Solved is there a code you can execute to tell you if you have issues with your machine

    hello guys yesterday i finally got my printer leveled right and printed parts last night and this morning when i went to print something it failed...
    Thread by: VBUZZ, Mar 30, 2017, 1 replies, in forum: Troubleshooting
  3. VBUZZ
    Post

    Solved ROBO3D R1 BED LEVELING

    THANK YOU ALL for all your help i messed with the m565 until i got it printing better than any 3d printer ive used so far but that does not say...
    Post by: VBUZZ, Mar 29, 2017 in forum: Troubleshooting
  4. VBUZZ
    Post

    Solved ROBO3D R1 BED LEVELING

    im just finding that out
    Post by: VBUZZ, Mar 28, 2017 in forum: Troubleshooting
  5. VBUZZ
    Post

    Solved ROBO3D R1 BED LEVELING

    ok thank ill keep working on it and let you know
    Post by: VBUZZ, Mar 28, 2017 in forum: Troubleshooting
  6. VBUZZ
    Post

    Solved ROBO3D R1 BED LEVELING

    ok then do i need to have an offset in the program set or no
    Post by: VBUZZ, Mar 28, 2017 in forum: Troubleshooting
  7. VBUZZ
    Post

    Solved ROBO3D R1 BED LEVELING

    ok this is what just happened i turned on the 3d printer connected to it with simplified 3d and homed it and it homed fine when to all the end...
    Post by: VBUZZ, Mar 28, 2017 in forum: Troubleshooting
  8. VBUZZ
    Post

    Solved ROBO3D R1 BED LEVELING

    i read the other guys post and decided to wait until finished version was out first
    Post by: VBUZZ, Mar 28, 2017 in forum: Troubleshooting
  9. VBUZZ
    Post

    Solved ROBO3D R1 BED LEVELING

    i did not install firm ware
    Post by: VBUZZ, Mar 28, 2017 in forum: Troubleshooting
  10. VBUZZ
    Post

    Solved ROBO3D R1 BED LEVELING

    i purchased this 3d printer used i got home and purchased simplified 3d and then i had to install only the usb driver so the printer would show up...
    Post by: VBUZZ, Mar 28, 2017 in forum: Troubleshooting
  11. VBUZZ
    Post

    Solved ROBO3D R1 BED LEVELING

    That is strange because when i just push the home button it moves to the limit switches and when i manualy type in g28 it does its homing moves...
    Post by: VBUZZ, Mar 28, 2017 in forum: Troubleshooting
  12. VBUZZ
    Post

    Solved ROBO3D R1 BED LEVELING

    OK THERE MUST HAVE BEEN A SHORT OR SOMETHING BECAUSE ITS WORKING NOW QUESTION THE G CODE FOR HOME IS NOT G28 RIGHT BECAUSE WHEN I DO THAT IT PUTS...
    Post by: VBUZZ, Mar 28, 2017 in forum: Troubleshooting
  13. VBUZZ
    Post

    Solved ROBO3D R1 BED LEVELING

    since im using simplefide 3d i even reloaded the stock firmware in case i messed something up in the settings
    Post by: VBUZZ, Mar 28, 2017 in forum: Troubleshooting
  14. VBUZZ
    Post

    Solved ROBO3D R1 BED LEVELING

    you think the switch might be bad ?
    Post by: VBUZZ, Mar 28, 2017 in forum: Troubleshooting