1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by XEMA

  1. XEMA
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    What are you using for your values? Somewhere for me to start.... Sent from my Pixel XL using Tapatalk
    Post by: XEMA, Mar 6, 2018 in forum: Mods and Upgrades
  2. XEMA
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    That's what I thought too, I have changed it from the -1.00 all the way to 0, doesn't seem to help. I will try the firmware this time. Sent from...
    Post by: XEMA, Mar 6, 2018 in forum: Mods and Upgrades
  3. XEMA
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    You think it would help solve my issue by changing the offset in the firmware? I have tried changing it via the LCD and the m851 command. Sent...
    Post by: XEMA, Mar 6, 2018 in forum: Mods and Upgrades
  4. XEMA
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    on 1.1.8 (R1+) as well, I can get to the point where I start printing the validation mesh pattern, but the nozzle is too close to the bed. Any...
    Post by: XEMA, Mar 6, 2018 in forum: Mods and Upgrades
  5. XEMA
    Post

    PET First print with PETG - thoughts?

    Looks good, but I would mess around with the temperatures, it appears as though you are running it a tad hot. When I run the transparent PETG, I...
    Post by: XEMA, Aug 2, 2016 in forum: Printing Filament
  6. XEMA
    Post

    Octoprint question

    I know this doesn't help too much, but I slice my STL's with S3D and upload them/print with no issues at all. Yes, remove that line you mentioned...
    Post by: XEMA, May 17, 2016 in forum: Mods and Upgrades
  7. XEMA
    Thread

    Unanswered Paint on underside of build plate?

    Anyone know what type of paint is used for the graphics on the underside of the glass build plate? Also, has anyone heard of anyone creating a...
    Thread by: XEMA, Apr 29, 2016, 3 replies, in forum: General Questions
  8. XEMA
    Thread

    Spaceclaim with STL Prep

    Wasn't able to find any other threads on this software package so figured I would post my 2 cents. I did the 15 day trial and liked it enough to...
    Thread by: XEMA, Apr 29, 2016, 0 replies, in forum: Software
  9. XEMA
    Thread

    Unanswered Lost Magnet - Replacement?

    So one of my magnets apparently wasn't glued in properly and has popped out and subsequently been lost. Does anyone know where I can get an exact...
    Thread by: XEMA, Apr 14, 2016, 2 replies, in forum: Troubleshooting
  10. XEMA
    Post

    First test of FLEKS 3D build plate kit

    Try heating it up on your bed/plate first, then gently but firmly flexing out the warp. If the center is high, put your thumbs on the high side...
    Post by: XEMA, Apr 11, 2016 in forum: Show and Tell
  11. XEMA
    Post

    First test of FLEKS 3D build plate kit

    I wouldn't give up on them, the one time I contacted them it did take awhile, but they did get back to me. Regarding the warped issue. Have you...
    Post by: XEMA, Apr 11, 2016 in forum: Show and Tell
  12. XEMA
    Post

    First test of FLEKS 3D build plate kit

    Here is the clip I re-designed based on one I found: http://www.thingiverse.com/thing:1465977 *Note: If printed properly, they should just clear...
    Post by: XEMA, Apr 4, 2016 in forum: Show and Tell