1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Unresolved Nozzle mushing prince

Discussion in 'Troubleshooting' started by Colin howe, Jul 20, 2016.

  1. Colin howe

    Colin howe New Member

    Joined:
    Jun 1, 2016
    Messages:
    6
    Likes Received:
    0
    I was wondering if anyone could help me out with something. My robo r1 is having problems when it starts doing the infill it seems to smoosh the nozzle into the print. I'm using mattercontrol from my prints and I'm not sure what I have to change in there to fix this.
     

    Attached Files:

    #1 Colin howe, Jul 20, 2016
  2. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    Is it pla ? Are you using an oiler?what temp are you printing at (just so we know the ballpark)
     
    #2 Geof, Jul 21, 2016
  3. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,915
    Likes Received:
    7,338
    Did you change anything? Update firmware, etc?
     
    #3 mark tomlinson, Jul 21, 2016
  4. Colin howe

    Colin howe New Member

    Joined:
    Jun 1, 2016
    Messages:
    6
    Likes Received:
    0
    It is pla. No oiler. Print temp 210
    I add a lcd controller not sure if that would have messed with the firmware.
    Is there anyway I can't reboot it back to factory settings and try it form there?
     
    #4 Colin howe, Jul 21, 2016
  5. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,915
    Likes Received:
    7,338
    Adding a controller does nothing to the firmware. You would need to edit that and upload it (some controllers will not work without editing the firmware)
     
    #5 mark tomlinson, Jul 21, 2016
    Last edited: Jul 21, 2016
  6. Ryan TeGantvoort

    Ryan TeGantvoort Active Member

    Joined:
    Mar 11, 2016
    Messages:
    343
    Likes Received:
    172
    Unless you grabbed the wrong firmware for your printer, when you installed the lcd controller? XXL or Full Graphics? If I remember right, the XXL you don't have to change anything but the Full Graphics you have to.
     
    #6 Ryan TeGantvoort, Jul 21, 2016
    mark tomlinson likes this.
  7. Colin howe

    Colin howe New Member

    Joined:
    Jun 1, 2016
    Messages:
    6
    Likes Received:
    0
    It is a smart lcd and I had to go into arduino and do something for it to work
    But I watch a video on how to do it. When I set up the controller did i mess something up and that's why this is happening?
     
    #7 Colin howe, Jul 21, 2016
  8. Ryan TeGantvoort

    Ryan TeGantvoort Active Member

    Joined:
    Mar 11, 2016
    Messages:
    343
    Likes Received:
    172
    Which printer do you have? Did you get the correct firmware?
     
    #8 Ryan TeGantvoort, Jul 21, 2016
  9. Colin howe

    Colin howe New Member

    Joined:
    Jun 1, 2016
    Messages:
    6
    Likes Received:
    0
    I have the robo r1
     
    #9 Colin howe, Jul 21, 2016
  10. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    What firmware did you use
     
    #10 Geof, Jul 21, 2016
    Last edited by a moderator: Jul 21, 2016

Share This Page