1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 8 of 10
  1. tkoco
    Post

    Touchscreen Issue

    I noticed that you posted the same question in both the C2 and R2 printer Troubleshooting forums. What is the model of printer which you have? C2...
    Post by: tkoco, Feb 8, 2020 in forum: Troubleshooting
  2. tkoco
    Post

    Touchscreen Issue

    Did you backup your software before applying the update?
    Post by: tkoco, Feb 7, 2020 in forum: Troubleshooting
  3. tkoco
    Post

    Resin printers

    Angus of Makers Muse was saying the same advise.
    Post by: tkoco, Feb 4, 2020 in forum: Off Topic
  4. tkoco
    Post

    Flexplate system for the R2 Printer

    @Lance Weston , here is a suggestion. Why not remove the Flexplate surface and substitute a glass plate (with clamps). Then do a print bed preheat...
    Post by: tkoco, Feb 4, 2020 in forum: Mods and Upgrades
  5. tkoco
    Post

    Flexplate system for the R2 Printer

    Thank you for the feedback. It will certainly help other folks who have a V1 print bed and wish to install the Flexplate mod.
    Post by: tkoco, Feb 3, 2020 in forum: Mods and Upgrades
  6. tkoco
    Post

    Resin printers

    I have some models which do not print nice with a C2 or R2 printer. So, I am considering a resin printer. Thank you for the advise.
    Post by: tkoco, Feb 3, 2020 in forum: Off Topic
  7. tkoco
    Post

    Flexplate system for the R2 Printer

    The Flexplate mod does not guarantee the spec of flatness which you are looking for. I ran into the same issue with the print bed of my C2 printer...
    Post by: tkoco, Feb 2, 2020 in forum: Mods and Upgrades
  8. tkoco
    Post

    Flexplate system for the R2 Printer

    Interesting problem. Is the magnet matrix fully seated to the print bed? An observation / question: Is the 0.2 mm the gap at the edge as...
    Post by: tkoco, Feb 2, 2020 in forum: Mods and Upgrades
  9. tkoco
    Thread

    Resin printers

    Any of you have experience with resin printers? Any recommendations for brand of printer?
    Thread by: tkoco, Feb 2, 2020, 28 replies, in forum: Off Topic
  10. tkoco
    Post

    Palette 2/Palette 2 Pro

    Would you mind if we move the above posting to the Projects area?
    Post by: tkoco, Feb 1, 2020 in forum: Projects
  11. tkoco
    Post

    How can i solve problem related to STONE LCD screen 7

    I believe that this article should help you: https://www.stoneitech.com/news/sharing/arduino-lcd-display-project.html
    Post by: tkoco, Feb 1, 2020 in forum: General Questions
  12. tkoco
    Post

    Flexplate system for the R2 Printer

    I don't see any reason why it would not fit a V1 bed. The differences between V1 and V2 print beds has to do with the power connection at the rear...
    Post by: tkoco, Jan 30, 2020 in forum: Mods and Upgrades
  13. tkoco
    Post

    Palette 2/Palette 2 Pro

    Thank you.
    Post by: tkoco, Jan 29, 2020 in forum: Projects
  14. tkoco
    Post

    Palette 2/Palette 2 Pro

    Would you mind writing up the set-up, software and workflow needed to accomplish a print job? Additional info like how the model is treated (one...
    Post by: tkoco, Jan 29, 2020 in forum: Projects
  15. tkoco
    Post

    Partially Solved Occasional Layer slip

    It will be interesting to find out the cause of the problem. How about an image showing the "slip" problem?
    Post by: tkoco, Jan 26, 2020 in forum: Troubleshooting
  16. tkoco
    Profile Post

    Lurking about 8)

    Lurking about 8)
    Status update by tkoco, Jan 24, 2020
  17. tkoco
    Thread

    Solved Remote viewing of a print job

    1) a remote camera will need to be installed on the C2 printer. Click on the word "Instructions" in the following: URL:...
    Thread by: tkoco, Jan 24, 2020, 0 replies, in forum: Software
  18. tkoco
    Post

    Solved Cura 4.1 alert (Obsolete)

    Update: Cura is now 4.4.1 as of this writing, so this thread is obsolete
    Post by: tkoco, Jan 24, 2020 in forum: Software
  19. tkoco
    Post

    Robo C2 Image download link.

    Playing the devil's advocate: Since they had a functional tech support at the time, they knew which RoboOS image to send to the end user based on...
    Post by: tkoco, Jan 23, 2020 in forum: Software
  20. tkoco
    Post

    FAQ C2

    Concerning RoboOS software: The C2 printer has 2 flavors of RoboOS, HDMI LCD screen and non-HDMI LCD screen. The LCD screen drivers in the...
    Post by: tkoco, Jan 23, 2020 in forum: Troubleshooting
Showing results 141 to 160 of 190 Next >
Search Again
Page 8 of 10