1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. TheGlutton
    Post

    Unresolved 3d Systems Cube3 Quality > My ROBO R1

    @WheresWaldo sorry for the mixup! I edited my post above to say that all of the example photos in that post were a .2mm printed at 50mm/s speed....
    Post by: TheGlutton, Jul 31, 2016 in forum: Troubleshooting
  2. TheGlutton
    Post

    Unresolved 3d Systems Cube3 Quality > My ROBO R1

    Time for an update. Made big strides, but still having some issues. I used the Paper Leveling method and found that the right side of the...
    Post by: TheGlutton, Jul 31, 2016 in forum: Troubleshooting
  3. TheGlutton
    Post

    Unresolved 3d Systems Cube3 Quality > My ROBO R1

    @Geof Thank you for the offer, I may take you up on it in the future :)
    Post by: TheGlutton, Jul 28, 2016 in forum: Troubleshooting
  4. TheGlutton
    Post

    Unresolved 3d Systems Cube3 Quality > My ROBO R1

    @Ryan TeGantvoort Thank you, I have just updated the XY_Jerk to 12, and the acceleration settings to {600, 600, 100, 10000}, added a belt...
    Post by: TheGlutton, Jul 28, 2016 in forum: Troubleshooting
  5. TheGlutton
    Post

    Unresolved 3d Systems Cube3 Quality > My ROBO R1

    I just finished a 5hr 20min Benchy, and it looks a little better, but MAN was that painfully slow... @mark tomlinson Speed definitely kills, but...
    Post by: TheGlutton, Jul 28, 2016 in forum: Troubleshooting
  6. TheGlutton
    Thread

    Unresolved 3d Systems Cube3 Quality > My ROBO R1

    Hey Everyone! I just want to start by saying thank you to all those who helped get me up and running through my last thread! :D Ok so I think I...
    Thread by: TheGlutton, Jul 28, 2016, 14 replies, in forum: Troubleshooting
  7. TheGlutton
    Post

    Solved New Printer Issues

    The control board is now running cool and my test cube is 20cm high :D The print quality is also imensly improved, I am going camping this weekend...
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  8. TheGlutton
    Post

    Solved Prints Short on Z axis

    Can confirm, my control board fan was not wired correctly and my 20cm calibration cubes were consistently coming out at 17mm high with terrible...
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  9. TheGlutton
    Post

    Solved New Printer Issues

    @danzca6 Thank you! You are spot on, I think that I have the z-axis issue fixed (with my control board fan now actually running) after this cube...
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  10. TheGlutton
    Post

    Solved New Printer Issues

    OK, I used these settings for PLA: http://wiki.eccmakers.com/index.php?title=Robo3d_Settings_for_Cura And was able to get the quality to improve...
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  11. TheGlutton
    Post

    Solved New Printer Issues

    Latest test cube still almost exactly 17mm, or 3mm to short... I am at a complete loss, in addition to being short the print quality is quite...
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  12. TheGlutton
    Post

    Solved New Printer Issues

    OK, I have modified my Gcode by adding the lines from this thread by @Ben R:...
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  13. TheGlutton
    Post

    Solved New Printer Issues

    I have tried: -Powercycling the printer -setting z-offset to .9 -setting z-offset to 0 -setting z offset to -1 -z-offset 1.0 -Printing with...
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  14. TheGlutton
    Post

    Solved New Printer Issues

    Re-flashing the firmware did not fix the printing to close to the bed issue, i re ran M503: > M503 < echo:Steps per unit: < echo: M92 X80.00...
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  15. TheGlutton
    Post

    Solved New Printer Issues

    Since the firmware upgrade my printer tries to print with the extruder too close to the bed, zero filament comes out and the printer is etching...
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  16. TheGlutton
    Post

    Solved New Printer Issues

    I just 'Uploaded' the firmware using Arduino, I will start a new cube and see if there are any improvements.
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  17. TheGlutton
    Post

    Solved New Printer Issues

    I added photos of my last cube above, here is the results of the M503: ->M503 <-echo:Steps per unit: <-echo: M92 X80.00 Y80.00 Z2560.00...
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  18. TheGlutton
    Post

    Solved New Printer Issues

    @Geof I am not sure exactly? There is a top/bottom thickness setting? Here are screenshots of my settings: [ATTACH] [ATTACH] [ATTACH]
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  19. TheGlutton
    Post

    Solved New Printer Issues

    Well, the printer is putting the top layer on the cube now, and it is still clearly short :( So far in an effort to get a 20mm tall cube I have:...
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  20. TheGlutton
    Post

    Solved New Printer Issues

    I used Matter Control and the hex file from @mark tomlinson 's post, and am printing another cube now, will post results soon.
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 26 Next >
Search Again
Page 1 of 2