1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 9 of 10
  1. Geof
    Post

    Solved R1+ Broken hotend?

    R2 and c2 hotends are identical except that silly 19v while R2 is 24v. R1 is 12v
    Post by: Geof, Sep 16, 2019 in forum: Troubleshooting
  2. Geof
    Post

    Solved R1+ Broken hotend?

    Both are the same hexagon as far as I can tell just the electronics are different
    Post by: Geof, Sep 16, 2019 in forum: Troubleshooting
  3. Geof
    Post

    Bed not heating

    Sounds like your either min temp or max temping. Are there any errors on your screen or in your log on the interface ?
    Post by: Geof, Sep 16, 2019 in forum: Troubleshooting
  4. Geof
    Thread

    Ultimaker 2+ Extended

    hey All, I’ve decided to scale back my buisness and am selling off some machines I no longer need. First one is my Ultimaker 2+ Extended....
    Thread by: Geof, Sep 5, 2019, 0 replies, in forum: Off Topic
  5. Geof
    Post

    Glow In The Dark filaments

    Never tried leds behind glowfill. I’d assume you’d want as close to green as you can get, blue and green mixed doesn’t make green I’d think :)
    Post by: Geof, Aug 31, 2019 in forum: Off Topic
  6. Geof
    Post

    PEI Sheets precut with 3m

    Sorry neither for the R1...whambam is looking into it
    Post by: Geof, Aug 25, 2019 in forum: Mods and Upgrades
  7. Geof
    Post

    PEI Sheets precut with 3m

    Buildtak has a 100.00 system, nothing else yet
    Post by: Geof, Aug 25, 2019 in forum: Mods and Upgrades
  8. Geof
    Post

    R2 reports constant, incorrect extruder temperature

    I thought there were differences between the boards- can check my two units tonight but I believe it wasn’t a big deal and should work without...
    Post by: Geof, Aug 21, 2019 in forum: Troubleshooting
  9. Geof
    Post

    Solved What is a good RAMP replacement board?

    12v :)
    Post by: Geof, Aug 19, 2019 in forum: Troubleshooting
  10. Geof
    Post

    Solved R1 + bed not heating up.

    Yes polarity matters there, good catch. In the thread I believe it mentions that for the specific board I had bought but it applies to everything...
    Post by: Geof, Aug 7, 2019 in forum: Troubleshooting
  11. Geof
    Post

    Solved R1 + bed not heating up.

    I strongly suggest you just replace the ramps board. It’s common that a loose connection fries that and the heather stops working - and you may...
    Post by: Geof, Aug 6, 2019 in forum: Troubleshooting
  12. Geof
    Post

    Solved R1 + bed not heating up.

    I have a machine that needs rewired, if I ever get around to it I’ll try to replace those crappy photos younger me took :) I think Mark and I did...
    Post by: Geof, Aug 6, 2019 in forum: Troubleshooting
  13. Geof
    Post

    Solved R1 + bed not heating up.

    Hey all, unfortunately that was multiple computers ago and they have been lost. What do you have questions about and I can try to help you, I’ll...
    Post by: Geof, Aug 6, 2019 in forum: Troubleshooting
  14. Geof
    Post

    Selling a Palette+

    Might try the mighty eBay and post some pics of some fancy multicolor prints. Might intrigue someone enough to not notice there is a newer...
    Post by: Geof, Jul 30, 2019 in forum: Mods and Upgrades
  15. Geof
    Post

    Community Favorite Marlin 2.0.x release for Robo R1+

    Oh not at all. It’s still somewhat active, thought you had a question still :) new thread for that, thanks and praise anywhere! :)
    Post by: Geof, Jul 25, 2019 in forum: Mods and Upgrades
  16. Geof
    Post

    Community Favorite Marlin 2.0.x release for Robo R1+

    I would start a new thread :)
    Post by: Geof, Jul 25, 2019 in forum: Mods and Upgrades
  17. Geof
    Post

    Selling a Palette+

    Best of luck with your sale ! With the pallete 2 out for 500 it might be a rough sale but I’d bet someone will be interested
    Post by: Geof, Jul 24, 2019 in forum: Mods and Upgrades
  18. Geof
    Post

    Has Robo closed up shop?

    This
    Post by: Geof, Jul 16, 2019 in forum: General Questions
  19. Geof
    Post

    Has Robo closed up shop?

    Hey sorry for the delay, I see you’ve got multiple answers already, apologies for the delay. Hit me up if you have any questions still
    Post by: Geof, Jul 7, 2019 in forum: General Questions
  20. Geof
    Post

    Has Robo closed up shop?

    I did ! The E3 is a flash forge adventurer 3 with spare bed and hot end included, 2 hour online training and a trial to my stem kits (and a 2...
    Post by: Geof, Jul 1, 2019 in forum: General Questions
Showing results 161 to 180 of 196 Next >
Search Again
Page 9 of 10