1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 3 of 5
  1. Robert Foreman
    Post

    Solved my robo 3d r1+ has problems with Z axis

    That happened to me when I got mine. Take the top off of the Robo this will allow you to see the switch on the left. The bottom picture is how it...
    Post by: Robert Foreman, May 14, 2016 in forum: Troubleshooting
  2. Robert Foreman
    Post

    Solved my robo 3d r1+ has problems with Z axis

    In matter control there should be a terminal window and you would type G28( this homes all axis. also the G is uppercase other wise the command...
    Post by: Robert Foreman, May 14, 2016 in forum: Troubleshooting
  3. Robert Foreman
    Post

    Solved my robo 3d r1+ has problems with Z axis

    Have you run the G28 code? I have found that anytime I have to turn the printer off and then back on I have to run the G28 command to home all axiss.
    Post by: Robert Foreman, May 14, 2016 in forum: Troubleshooting
  4. Robert Foreman
    Post

    What is the best way to remove the heating element from the glass?

    Your welcome. It is the best upgrade I have done so far. I have some PEI sheets also but have not seen a need to use them yet. :)
    Post by: Robert Foreman, May 13, 2016 in forum: Mods and Upgrades
  5. Robert Foreman
    Post

    What is the best way to remove the heating element from the glass?

    No problem with weight that I can see. The print quality so far has been great. Here is a picture of two playing card holders I printed. The one...
    Post by: Robert Foreman, May 12, 2016 in forum: Mods and Upgrades
  6. Robert Foreman
    Post

    PEI glass as a bed substitute

    I just finished replacing my glass bed with an 10"x15"x1/4" aluminum plate. I remounted the stock heater on it and I am printing on it with only...
    Post by: Robert Foreman, May 12, 2016 in forum: Mods and Upgrades
  7. Robert Foreman
    Post

    What is the best way to remove the heating element from the glass?

    Thanks. That is going to be my next step.
    Post by: Robert Foreman, May 8, 2016 in forum: Mods and Upgrades
  8. Robert Foreman
    Post

    What is the best way to remove the heating element from the glass?

    Have you got instructions or pictures on how to set that up. I at some point want to replace the heater. What power supply are you using?
    Post by: Robert Foreman, May 8, 2016 in forum: Mods and Upgrades
  9. Robert Foreman
    Post

    What is the best way to remove the heating element from the glass?

    Thanks :). I am very happy with it and now I don't have to worry about the glass breaking. I am going to run to Lowes today and get some...
    Post by: Robert Foreman, May 7, 2016 in forum: Mods and Upgrades
  10. Robert Foreman
    Post

    What is the best way to remove the heating element from the glass?

    I need to get more cork. The cork that was on there is a little damaged and is catching on the pullys. Ant suggestion on what type on insulator to...
    Post by: Robert Foreman, May 7, 2016 in forum: Mods and Upgrades
  11. Robert Foreman
    Post

    What is the best way to remove the heating element from the glass?

    Ok here are some pictures.
    Post by: Robert Foreman, May 6, 2016 in forum: Mods and Upgrades
  12. Robert Foreman
    Post

    What is the best way to remove the heating element from the glass?

    I am going to stick with the stock for the time being. I tested it last night before I took it apart by laying the aluminum plate on top of the...
    Post by: Robert Foreman, May 6, 2016 in forum: Mods and Upgrades
  13. Robert Foreman
    Post

    What is the best way to remove the heating element from the glass?

    I will go with this at a later date. My wallet is telling I can't spend any more money for now. So I am going to have to go with the stock heater...
    Post by: Robert Foreman, May 6, 2016 in forum: Mods and Upgrades
  14. Robert Foreman
    Post

    What is the best way to remove the heating element from the glass?

    1\4 inch. I am going to mount it when I get home tonight. I will post pictures when I am done.
    Post by: Robert Foreman, May 6, 2016 in forum: Mods and Upgrades
  15. Robert Foreman
    Post

    What is the best way to remove the heating element from the glass?

    @WZ9V I ordered 10x15 one from https://www.midweststeelsupply.com/store/castaluminumplate It was about $40 with shipping. @mark tomlinson. It...
    Post by: Robert Foreman, May 6, 2016 in forum: Mods and Upgrades
  16. Robert Foreman
    Thread

    What is the best way to remove the heating element from the glass?

    I am wanting to replace my glass bed with an aluminum plate. I received the plate on Monday. What is the best way to remove the heating element...
    Thread by: Robert Foreman, May 5, 2016, 51 replies, in forum: Mods and Upgrades
  17. Robert Foreman
    Post

    Printer Number 2

    My other printer is the FlashForge Creator Pro.
    Post by: Robert Foreman, Apr 21, 2016 in forum: Projects
  18. Robert Foreman
    Post

    Aluminum Heated Bed

    Thanks every I will look into Midwest steel for the plate and look at Amazon the the 3M double sided sheet. Thanks again. :)
    Post by: Robert Foreman, Apr 21, 2016 in forum: Mods and Upgrades
  19. Robert Foreman
    Post

    Aluminum Heated Bed

    How is the current glass bed attached the heated bed? I am looking into getting a 1/4" aluminum plate and want to reattach the heated bed that is...
    Post by: Robert Foreman, Apr 21, 2016 in forum: Mods and Upgrades
  20. Robert Foreman
    Post

    Unresolved What cause this in the print?

    Yes I am watching the E3D Titan thread very close. Yea when I say direct drive I want some thing like I have on my Flashforge Creator Pro. the...
    Post by: Robert Foreman, Apr 18, 2016 in forum: Troubleshooting
Showing results 41 to 60 of 88 Next >
Search Again
Page 3 of 5