1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 4 of 6
  1. tiagomaricate
    Post

    How can I improve this printing and remove the "waves"

    They are ok (I think).
    Post by: tiagomaricate, Aug 8, 2020 in forum: Troubleshooting
  2. tiagomaricate
    Post

    Could you help a noob to upgrade the pip?

    I have no problem replacing the original interface for another one, with customized features. I'm a designer, so build a good interface is not a...
    Post by: tiagomaricate, Aug 8, 2020 in forum: Mods and Upgrades
  3. tiagomaricate
    Post

    How can I improve this printing and remove the "waves"

    But the wavy is on the lateral, related to the X/Y axis
    Post by: tiagomaricate, Aug 8, 2020 in forum: Troubleshooting
  4. tiagomaricate
    Thread

    Can't store the print job on the printer SD card (octoprint and cura)

    Not sure if I should post this here, on in the Octoprint forums or in the Cura forums... I installed on Cura the plugin to connect with Octoprint...
    Thread by: tiagomaricate, Aug 8, 2020, 6 replies, in forum: General Questions
  5. tiagomaricate
    Post

    Could you help a noob to upgrade the pip?

    So what is the last version of pip I can use? Ans about to install Kivvy on the last pip version? No way?
    Post by: tiagomaricate, Aug 8, 2020 in forum: Mods and Upgrades
  6. tiagomaricate
    Post

    How can I improve this printing and remove the "waves"

    I'm doing a lot of tests changing the jerk and speed... soon I back to show the results.
    Post by: tiagomaricate, Aug 8, 2020 in forum: Troubleshooting
  7. tiagomaricate
    Post

    How can I improve this printing and remove the "waves"

    Maybe check jerk and acceleration?
    Post by: tiagomaricate, Aug 5, 2020 in forum: Troubleshooting
  8. tiagomaricate
    Post

    Could you help a noob to upgrade the pip?

    So basically is like updated octoprint don't support the "old/non updated" version of Robo OS/LCD plugin?
    Post by: tiagomaricate, Aug 5, 2020 in forum: Mods and Upgrades
  9. tiagomaricate
    Post

    R2 Connectors

    I'm working on a way to put the contacts under the bed, like the V1. And replace the back connector for another one, more resistant and on the...
    Post by: tiagomaricate, Aug 5, 2020 in forum: General Questions
  10. tiagomaricate
    Thread

    Could you help a noob to upgrade the pip?

    Well... almost a complete noob. Despite I had worked with front end and some servers, I never go to deep. Also, I have no idea if the printer...
    Thread by: tiagomaricate, Aug 5, 2020, 10 replies, in forum: Mods and Upgrades
  11. tiagomaricate
    Thread

    How can I improve this printing and remove the "waves"

    I'm tunning all the settings and face this problem on the lateral of printing. Any suggestion?
    Thread by: tiagomaricate, Aug 5, 2020, 11 replies, in forum: Troubleshooting
  12. tiagomaricate
    Post

    R2 Connectors

    Tks dude!!!
    Post by: tiagomaricate, Aug 5, 2020 in forum: General Questions
  13. tiagomaricate
    Post

    No BuildTak Print Surface compatible

    I will test it! I separate some different tapes to try and discover what the UV sensor sees.
    Post by: tiagomaricate, Jul 28, 2020 in forum: Troubleshooting
  14. tiagomaricate
    Post

    Wrong Z-axis value when printing

    Looks the UV sensor only detects the original buildtak. If I use a magic maker on the "generic" builtak, the sensors detect it.
    Post by: tiagomaricate, Jul 28, 2020 in forum: Troubleshooting
  15. tiagomaricate
    Thread

    Interchangeable universal printing table

    I did several experiments and tests to create a printing table system in which I could change it without much work. In this way, it will be...
    Thread by: tiagomaricate, Jul 26, 2020, 0 replies, in forum: Off Topic
  16. tiagomaricate
    Post

    Wrong Z-axis value when printing

    Looks the UV sensor simply doesn't detect it... but I will try. Maybe the sensor detects, but with a very different values.
    Post by: tiagomaricate, Jul 26, 2020 in forum: Troubleshooting
  17. tiagomaricate
    Thread

    No BuildTak Print Surface compatible

    So... I did several tests with a lot of different print surfaces and no one works. Only the original one. If I put any other print surface, the IR...
    Thread by: tiagomaricate, Jul 26, 2020, 7 replies, in forum: Troubleshooting
  18. tiagomaricate
    Post

    Wrong Z-axis value when printing

    Yes is the last one, 1.2.6
    Post by: tiagomaricate, Jul 26, 2020 in forum: Troubleshooting
  19. tiagomaricate
    Post

    Wrong Z-axis value when printing

    Yep it is
    Post by: tiagomaricate, Jul 26, 2020 in forum: Troubleshooting
  20. tiagomaricate
    Thread

    Wrong Z-axis value when printing

    Z-offset has done. Bed calibration is done. Auto-leveling has done. And it still putting the bed on the wrong height. Any idea? [MEDIA]
    Thread by: tiagomaricate, Jul 24, 2020, 8 replies, in forum: Troubleshooting
Showing results 61 to 80 of 102 Next >
Search Again
Page 4 of 6