1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 5 of 5
  1. Robert55
    Post

    Anyone try 20 microns yet?

    Geof, I'd appreciate some advice on the smaller nozzles. I tried a .2mm and it clogged in about 5 minutes...lol...of course, I forgot to put in a...
    Post by: Robert55, Feb 11, 2017 in forum: Show and Tell
  2. Robert55
    Post

    Solved Robo3D R1 smoke out back and wont power up

    You let the Magic Smoke out!!! Everyone knows all electrical stuff runs on Magic Smoke, but only as long as it doesn't escape. Even big-ass power...
    Post by: Robert55, Jan 27, 2017 in forum: Troubleshooting
  3. Robert55
    Post

    Just got E3Dv6 but have an issue

    My whole X-carriage and Wade's is Hatchbox Glow-in-the-dark PLA. I've had no problems at all.
    Post by: Robert55, Jan 27, 2017 in forum: Mods and Upgrades
  4. Robert55
    Post

    Solved Sudden problem with extruder and printing

    Check your RAMPs board cooling - flaky fan, wiring, whatever. I just went through a bunch of this stuff. I had cut a larger hole in the bottom...
    Post by: Robert55, Jan 27, 2017 in forum: Troubleshooting
  5. Robert55
    Post

    Answered Extruder Stepper Motor Skipping

    I noticed. Because of the slight difference in size between the Hex and E3D, I eventually cracked my X Axis and Extruder (Gorilla Glue for...
    Post by: Robert55, Jan 21, 2017 in forum: Troubleshooting
  6. Robert55
    Post

    Answered Extruder Stepper Motor Skipping

    Mark J. Neither, actually. It was a switch to the E3D V6 Volcano. Longer heater block stuck out into the air stream of the new mount for the stock...
    Post by: Robert55, Jan 20, 2017 in forum: Troubleshooting
  7. Robert55
    Post

    Answered Extruder Stepper Motor Skipping

    I had the same thing happen. Went through everything your doing and it still did it. Ended up being excessive back pressure from the hot end....
    Post by: Robert55, Jan 20, 2017 in forum: Troubleshooting
  8. Robert55
    Post

    Solved Moving the Extruder with Simplify3d

    https://www.simplify3d.com/support/videos/
    Post by: Robert55, Jan 15, 2017 in forum: Troubleshooting
  9. Robert55
    Post

    Odd?? but still printed?

    How many top layers did you specify??
    Post by: Robert55, Jan 3, 2017 in forum: General Questions
  10. Robert55
    Post

    Saved Settings

    It looks like exporting and saving the g-code is the only option at this point. Only problem is, it overrides Mattercontrol's present settings by...
    Post by: Robert55, Jan 2, 2017 in forum: General Questions
  11. Robert55
    Post

    Solved My Robo R1+ Error

    In my case, the increased filament flow with a 1mm nozzle didn't help. Some ceramic tape (try Amazon), and some CPU thermal paste on the heater...
    Post by: Robert55, Dec 21, 2016 in forum: Troubleshooting
  12. Robert55
    Post

    Solved My Robo R1+ Error

    I've had that happen running an E3D Volcano - do you run a parts cooling fan?? Is the heater block insulated (tape or sock)?? If the parts cooling...
    Post by: Robert55, Dec 20, 2016 in forum: Troubleshooting
  13. Robert55
    Post

    Solved PEI Upgrade and z-offset

    Lower left on Simplfy3D - "Edit process settings", then G-Code tab, again lower left "Global G-Code Offsets."
    Post by: Robert55, Nov 3, 2016 in forum: General Questions
  14. Robert55
    Post

    Unresolved Z-axis would be up to the selfish.

    Mine only does that when the X-Axis carriage bars are not exactly parallel with the printer bed. Then the Z axis switches are triggered at...
    Post by: Robert55, Sep 9, 2016 in forum: Troubleshooting
Find older messages
Showing results 81 to 94 of 94
Search Again
Page 5 of 5