1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Etan15
    Post

    First test of FLEKS 3D build plate kit

    I am happy you guys have it working. I gave gone the route of Kapton tape and have not looked back. Added an E3d hotend as well. Sent from my...
    Post by: Etan15, Jul 15, 2016 in forum: Show and Tell
  2. Etan15
    Post

    Cura 2.1 Beta

    Thought you might find this interesting if you are a Cura user. I found a Cura release by a company called "Type A Machine" and the software is...
    Post by: Etan15, Jun 12, 2016 in forum: Software
  3. Etan15
    Post

    First test of FLEKS 3D build plate kit

    They replied about 4 weeks after my initial email to them. Sent from my VS985 4G using Tapatalk
    Post by: Etan15, May 23, 2016 in forum: Show and Tell
  4. Etan15
    Post

    First test of FLEKS 3D build plate kit

    Hey all, I received an email from Fleks3D today in regards to my inquiry about the warped plates. They refunded my money. It took a little bit...
    Post by: Etan15, Apr 26, 2016 in forum: Show and Tell
  5. Etan15
    Post

    First test of FLEKS 3D build plate kit

    That is good. I am using Kapton tape and have not had a bad print in over 2 weeks. Sent from my VS985 4G using Tapatalk
    Post by: Etan15, Apr 23, 2016 in forum: Show and Tell
  6. Etan15
    Post

    First test of FLEKS 3D build plate kit

    @KTMDirtFace with Fleks3D plates that are bowed it is very difficult to work with. Be thankful you received flat plates. Looks like I donated...
    Post by: Etan15, Apr 16, 2016 in forum: Show and Tell
  7. Etan15
    Post

    First test of FLEKS 3D build plate kit

    I think Kapton tape should be included in the box when you get a Robo. Prints have been fantastic since moving to the Kapton tape. I Sent from...
    Post by: Etan15, Apr 16, 2016 in forum: Show and Tell
  8. Etan15
    Post

    First test of FLEKS 3D build plate kit

    Well, I had all the issues you listed and the company still has not returned my email and it has been 2 weeks. I have resorted to Kapton tape and...
    Post by: Etan15, Apr 14, 2016 in forum: Show and Tell
  9. Etan15
    Post

    First test of FLEKS 3D build plate kit

    I put a dumbel in the middle of one for almost 2 days and it did nothing to the warp. Pretty strong stuff. I will try to contact them again....
    Post by: Etan15, Apr 11, 2016 in forum: Show and Tell
  10. Etan15
    Post

    First test of FLEKS 3D build plate kit

    I have given up on the Fleks3D. The two plates that were sent to me were warped and I contacted them 2 times with no feedback as of a week and a...
    Post by: Etan15, Apr 11, 2016 in forum: Show and Tell
  11. Etan15
    Post

    First test of FLEKS 3D build plate kit

    The corner clips would work for one of the plates but not the other. One plate the middle bows up and the other plate the middle bows down....
    Post by: Etan15, Apr 1, 2016 in forum: Show and Tell
  12. Etan15
    Post

    First test of FLEKS 3D build plate kit

    Officially not happy with the Fleks3D. The two plates that came with mine were warped from the start and did not sit on the plate flat. During...
    Post by: Etan15, Mar 31, 2016 in forum: Show and Tell
  13. Etan15
    Post

    First test of FLEKS 3D build plate kit

    Got mine yesterday and started installing today. My plates are a bit warped so I am dealing with that right now. Sort of thinking I should just...
    Post by: Etan15, Mar 31, 2016 in forum: Show and Tell
  14. Etan15
    Post

    PETG suggestions?

    Thanks for all the info! Did you upgrade the leadscrew on a R1+?
    Post by: Etan15, Mar 31, 2016 in forum: Printing Filament
  15. Etan15
    Post

    PETG suggestions?

    So are all of you speeds set to 50mm/sec? Do you set the first layer to print slower? What about inside and outside walks? Looks really good....
    Post by: Etan15, Mar 31, 2016 in forum: Printing Filament
  16. Etan15
    Post

    First test of FLEKS 3D build plate kit

    Mine did not come with the puck either. I am installing later tonight. Sent from my VS985 4G using Tapatalk
    Post by: Etan15, Mar 31, 2016 in forum: Show and Tell
  17. Etan15
    Post

    Things I have learned my first 2 weeks

    @GAmbrosio Based on this: Using the levelling puck: Use if the nozzle is hot while performing the self-leveling procedure. If the nozzle is...
    Post by: Etan15, Mar 27, 2016 in forum: Show and Tell
  18. Etan15
    Post

    Things I have learned my first 2 weeks

    After a failed overnight print with PET+ because the corner curled up I just placed my order for the 10"x10" Fleks3D build plate. @Bil Forshey -...
    Post by: Etan15, Mar 27, 2016 in forum: Show and Tell
  19. Etan15
    Post

    Things I have learned my first 2 weeks

    Here are my settings in MC. They are set to more than half what I normally print my quadcopter parts at. Are these still to fast? [ATTACH]
    Post by: Etan15, Mar 20, 2016 in forum: Show and Tell
  20. Etan15
    Post

    Things I have learned my first 2 weeks

    So another week has gone by and I had an idea to put my printer up on 3D Hubs. I figured I would see if it would be worth it and cost effective....
    Post by: Etan15, Mar 20, 2016 in forum: Show and Tell
Showing results 1 to 20 of 37 Next >
Search Again
Page 1 of 2