1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 3 of 4
  1. Gage
    Post

    Solved Losing Temp

    Well it won't hurt I guess to check it out. Guess I should look at switching to the standard RAMPS too.
    Post by: Gage, Aug 2, 2016 in forum: Troubleshooting
  2. Gage
    Post

    Solved Losing Temp

    I was looking at that thread last night. I have an R1+
    Post by: Gage, Aug 2, 2016 in forum: Troubleshooting
  3. Gage
    Post

    Solved Losing Temp

    What steps would I take to check the RAMPS. I have already put in a new 12v 30amp heater.
    Post by: Gage, Aug 2, 2016 in forum: Troubleshooting
  4. Gage
    Post

    Solved Losing Temp

    I have made sure the firmware was correct when I first installed the V6. Mark helped me solve a few firmware problems I was having. I read on...
    Post by: Gage, Aug 2, 2016 in forum: Troubleshooting
  5. Gage
    Post

    Solved Losing Temp

    Yes first time using this filament. I'm going to load some of the PLA I have been using and run a print to see if I can replicate the problem. I...
    Post by: Gage, Aug 2, 2016 in forum: Troubleshooting
  6. Gage
    Post

    Solved Losing Temp

    I'm using the ducted fan holders from thingiverse. I have checked the parts fan to make sure it is not blowing on the nozzle but just below it. I...
    Post by: Gage, Aug 2, 2016 in forum: Troubleshooting
  7. Gage
    Thread

    Solved Losing Temp

    Been printing for several months with my Robo after switching to the E3D V6 hotend, have loved the quality of the prints and playing with...
    Thread by: Gage, Aug 1, 2016, 29 replies, in forum: Troubleshooting
  8. Gage
    Post

    Ninjaflex

    Yeah I had it on Kapton and couldn't get the model freed. However I went two for two on my prints. Just use the settings suggested by NinjaFlex on...
    Post by: Gage, May 1, 2016 in forum: General Questions
  9. Gage
    Post

    Ninjaflex

    I will give this a try
    Post by: Gage, Apr 30, 2016 in forum: General Questions
  10. Gage
    Post

    Ninjaflex

    Guess I will try to ease up on my tolerances for the first layer.
    Post by: Gage, Apr 30, 2016 in forum: General Questions
  11. Gage
    Post

    Ninjaflex

    I found that thread and went ahead with the prints. Slow and steady and I am two for two in my prints of Ninjaflex now. Only issue I had was...
    Post by: Gage, Apr 30, 2016 in forum: General Questions
  12. Gage
    Thread

    Ninjaflex

    Hello all! Just ordered a spool of NinjaFlex and was wondering if anyone has tips for printing in this medium. I understand SLOW is needed. I...
    Thread by: Gage, Apr 29, 2016, 14 replies, in forum: General Questions
  13. Gage
    Post

    Solved PLA jamming

    Cool thanks!
    Post by: Gage, Apr 28, 2016 in forum: General Questions
  14. Gage
    Post

    Solved PLA jamming

    So you use a sponge instead of cotton ball? Does the PLA just punch through the sponge?
    Post by: Gage, Apr 28, 2016 in forum: General Questions
  15. Gage
    Post

    Solved PLA jamming

    Awesome! Will print an oiler out of ABS tonight. And by the way, you have been the first to answer all of my questions on here so major props on...
    Post by: Gage, Apr 27, 2016 in forum: General Questions
  16. Gage
    Post

    Solved PLA jamming

    After you made the oiler did it solve most of your issues with the PLA jamming so much?
    Post by: Gage, Apr 27, 2016 in forum: General Questions
  17. Gage
    Post

    Solved PLA jamming

    Thanks!
    Post by: Gage, Apr 27, 2016 in forum: General Questions
  18. Gage
    Thread

    Solved PLA jamming

    I have printed in both PLA and ABS, used PLA since I started printing and have just recently switched to using ABS with my E3D V6 after a very bad...
    Thread by: Gage, Apr 27, 2016, 16 replies, in forum: General Questions
  19. Gage
    Post

    Solved Starting layer height strange.

    Thanks for the info!
    Post by: Gage, Apr 16, 2016 in forum: Troubleshooting
  20. Gage
    Thread

    Solved Starting layer height strange.

    Hello all, Recently installed the E3D V6 to my Robo 3D R1 +plus, absolutely love it. Followed Mike Kelly's how to guide an was relatively simple....
    Thread by: Gage, Apr 15, 2016, 2 replies, in forum: Troubleshooting
Showing results 41 to 60 of 67 Next >
Search Again
Page 3 of 4