1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 4 of 4
  1. joea
    Thread

    Answered Print dimensions off.

    Printed the leadscrew adapter https://www.thingiverse.com/thing:1147438 as a test. The Z axis dimension came out pretty much spot on, which was a...
    Thread by: joea, Nov 20, 2019, 38 replies, in forum: Troubleshooting
  2. joea
    Thread

    Solved Threaded rod size

    Back on the case after a breather. I was having some issues with bad prints of "taller" objects and Z axis offset. Before I go into this any...
    Thread by: joea, Nov 20, 2019, 2 replies, in forum: General Questions
  3. joea
    Thread

    Partial Answer Design software?

    Not exclusive to R1, but, since that is what I have . . . Is there a "best" (easiest to learn and use) free (ish) software to design simple parts...
    Thread by: joea, Nov 19, 2019, 18 replies, in forum: General Questions
  4. joea
    Thread

    Partially Solved Test print failed.

    Trying a test print of "Car Grille Fastener" found on thingiverse, I had a failure. Part of it is attributable to the "nut" part not staying...
    Thread by: joea, Nov 17, 2019, 3 replies, in forum: Troubleshooting
  5. joea
    Thread

    Answered What do LED colors and flashes mean at USB side?

    From time to time I see Red or Green LED flashes at the USB connector port. What do they signify?
    Thread by: joea, Nov 16, 2019, 2 replies, in forum: General Questions
  6. joea
    Thread

    Solved Noisy Fan fix?

    Is there a fix for the noisy extruder fan? The tiny on on the right side, as facing the machine?
    Thread by: joea, Nov 14, 2019, 23 replies, in forum: General Questions
  7. joea
    Thread

    Solved Scale

    Using MatterControl. 1.5, which told me there was a printer firmware upgrade available. Installed it and ran into a scale problem. Eventually...
    Thread by: joea, Nov 14, 2019, 6 replies, in forum: Troubleshooting
  8. joea
    Thread

    Partial Answer No + X limit swtich. By Design?

    Title says it all. There is no switch to limit +X travel, so it can make some horrid noise when beating against the stop. I imagine one could be...
    Thread by: joea, Nov 14, 2019, 6 replies, in forum: General Questions
  9. joea
    Thread

    Solved R1 Z axis travels much further than X or Y for same input?

    While testing my R1 and looking at lead screws to determine if they were upgraded, I noticed when using Matter Control 1.5 in manual, that the Z...
    Thread by: joea, Nov 14, 2019, 28 replies, in forum: Troubleshooting
  10. joea
    Thread

    Solved Bed LED?

    I've not run into the answer yet. I see on this early R1, no big R on the printing, it does say "Still hot after LED goes out!", but I have seen...
    Thread by: joea, Nov 14, 2019, 3 replies, in forum: General Questions
  11. joea
    Thread

    Solved First attempt with a used early unit. Limit switch adjustments?

    Using Matter Control. I can use the manual axis controls fine. But . . . "Home" does not work in the Z axis, in that, it only moves upward,...
    Thread by: joea, Nov 13, 2019, 12 replies, in forum: Troubleshooting
  12. joea
    Thread

    Solved USB or COM port?

    So, I installed matter control 1.5 and it will not detect the printer. When I attempt a manual setup it says available ports are COM1 and COM2....
    Thread by: joea, Nov 13, 2019, 3 replies, in forum: General Questions
  13. joea
    Thread

    Solved Power on, what to expect?

    For an early version R1, what should one expect when powering the unit up, besides fan noise, when powering up without a computer attached? The...
    Thread by: joea, Nov 13, 2019, 2 replies, in forum: General Questions
  14. joea
    Thread

    Solved Connecting hardware specs?

    Will the build documents have details about attachment hardware, such as the size of the screws holding the "cover" onto the base of an R1 early...
    Thread by: joea, Nov 12, 2019, 12 replies, in forum: General Questions
  15. joea
    Thread

    Solved Mystery Part?

    Just got a used, early version R1 at an estate sale. No chance to test it or get much information about it. While I attempt to get up to speed...
    Thread by: joea, Nov 12, 2019, 3 replies, in forum: General Questions
Find older messages
Showing results 61 to 75 of 75
Search Again
Page 4 of 4