1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 5 of 7
  1. Avrution
    Post

    Solved R1+ / Marlin / Homing failed

    So, I haven't touched my printer in almost a year - got everything set back up again, but can't for the life of me remember how to do much. Things...
    Post by: Avrution, Mar 18, 2021 in forum: Troubleshooting
  2. AbbyV
    Post

    Solved Robo 1+ is “stuck up in the ceiling” and won’t come back down

    Thanks to help from several people we were able to manually screwed the bars down and then turned on the printer and when we tried to print it...
    Post by: AbbyV, Jan 26, 2019 in forum: Troubleshooting
  3. astro boy
    Post

    Solved Print quality when scaling up model

    Ok well I have had simplify support and after supplying them with my fff file, they said it should print normally and offered that it might...
    Post by: astro boy, Jan 16, 2018 in forum: Troubleshooting
  4. digitalsolo
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    I have only had one issue with RC6 thus far and it may have been a bad file on the SD card. Went to kick off a print via SD and it kicked my G29...
    Post by: digitalsolo, Apr 28, 2016 in forum: Mods and Upgrades
  5. danzca6
    Post

    E3D Titan Extruder

    Oh and taking a second look at centering of the hotend in the Titan this morning, it looks pretty centered on the depth measurement, but it is...
    Post by: danzca6, Apr 10, 2016 in forum: Mods and Upgrades
  6. Sean Carson
    Post

    Solved recalibrating printer. Where am I messing up?

    Somehow, I can never get this thing to print properly on the bed. Once again, it is hovering above the bed. G0 Z0 always goes back the same...
    Post by: Sean Carson, Apr 13, 2017 in forum: Troubleshooting
  7. jim3Dbot
    Post

    R1+ Auto-Level not really accurate

    My oH My oH My..........I just stumbled across your thread..............I have been fighting with auto-level for two 10hr days.....I have printed...
    Post by: jim3Dbot, Feb 3, 2016 in forum: General Questions
  8. OutsourcedGuru
    Post

    R2 Unresponsive

    In a case like this, it might be worth powering off the printer, twisting that center Z-changing rod to move the bed out of the way, opening up...
    Post by: OutsourcedGuru, Jul 11, 2017 in forum: Troubleshooting
  9. Jeff Lastofka
    Post

    Solved Y-axis offset adjustment

    I've searched for "offset" in forum titles and didn't find this, so..... My printer's always worked fine. All the prints are physically 3/4" off...
    Post by: Jeff Lastofka, Apr 10, 2016 in forum: Troubleshooting
  10. Wade Mann
    Post

    Print Bed Leveling Issue

    Thanks for the information tkoco. I will find a balance. As far as the painters tape goes, the buildtak sheet is under it. I will start printing...
    Post by: Wade Mann, Apr 14, 2019 in forum: Troubleshooting
  11. Russ_B
    Post

    Partial Answer Firmware Recommendation

    I tried that technique, and just ran a test print. It seemed to help with the X axis rods getting out of parallel with the bed, but my print...
    Post by: Russ_B, Sep 27, 2022 in forum: Troubleshooting
  12. Toro1966
    Post

    Solved Home and Z Offset Settings and Questions

    Hey guys - I learning a tremendous amount this printer due to the great folks on here but I still have a few questions and thought I post a...
    Post by: Toro1966, Jul 24, 2016 in forum: Troubleshooting
  13. jscottb
    Post

    R2 received and in production!

    Yeah, I plan to get one from the auto parts store this week :) I do think the temp is off on the bed a good bit. I have been resetting the offset...
    Post by: jscottb, Sep 17, 2017 in forum: Show and Tell
  14. TKCC71
    Post

    Unresolved Simplify 3D issue?

    Did I do this right? :) I pulled this from the print I was attempting. processName,Process1 ; applyToModels,Chest top center 1 ;...
    Post by: TKCC71, Mar 30, 2016 in forum: Troubleshooting
  15. danzca6
    Post

    E3D Titan Extruder

    Using the stock motor and stock carriage, I would think the only option would be to have the back of the extruder motor facing the front of the...
    Post by: danzca6, Apr 9, 2016 in forum: Mods and Upgrades
  16. KTMDirtFace
    Post

    KTMDirtFace's new R1+

    I think I may have found a way to get the Left to Right auto level to actually work. Still have issues with front to back though. So normally I...
    Post by: KTMDirtFace, Apr 10, 2016 in forum: Show and Tell
  17. racer
    Post

    Repurposing Pirate3d Buccaneer

    Hi Dragonsquirrel, The full set of buccaneer-gcode is located in a file in the root directory of the buccaneer. The file is called...
    Post by: racer, Jan 6, 2019 in forum: Off Topic
  18. Dragonsquirrel
    Post

    Repurposing Pirate3d Buccaneer

    Hi, I got hold of one of these recently, and although mine printed ok using the windows app, the scaling was off (100mm printed as 96mm or so) So...
    Post by: Dragonsquirrel, Aug 24, 2018 in forum: Off Topic
  19. nickster
    Post

    Solved PLEASE READ - Hotend Jam/Clogs? - Seasoning and an Oiler

    Hey Mark - I've needed to run Maker Geeks Raptor PLA recently instead of ABS and was having a bear of a time on my E3D V6. Crazy heat creep jams....
    Post by: nickster, Aug 16, 2016 in forum: Troubleshooting
  20. Connor1998
    Post

    Solved ALL axes homing centers off after E3D v6 install

    So, I have not installed any differing firmware than what was stock. I have checked wiring on all of the switches and it is all correct. I based...
    Post by: Connor1998, Nov 2, 2021 in forum: Troubleshooting
Showing results 81 to 100 of 129 Next >
Search Again
Page 5 of 7