1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 2
  1. Sylva
    Post

    Answered S3D on Reprap XXL screen Issues

    Side note: What kind of terminals are the endstop slip on terminals?
    Post by: Sylva, Jun 30, 2017 in forum: Troubleshooting
  2. Sylva
    Post

    Answered S3D on Reprap XXL screen Issues

    So, I'm a bit special... I forgot to put the bottom panel back on. So it's been running with no board cooling this whole time. I'll hook it up...
    Post by: Sylva, Jun 26, 2017 in forum: Troubleshooting
  3. Sylva
    Post

    Answered S3D on Reprap XXL screen Issues

    The one connected to the v6 hotend or the one that cools the arduino board?
    Post by: Sylva, Jun 25, 2017 in forum: Troubleshooting
  4. Sylva
    Post

    Answered S3D on Reprap XXL screen Issues

    So, the prints are finishing when hooked up to a computer.
    Post by: Sylva, Jun 25, 2017 in forum: Troubleshooting
  5. Sylva
    Post

    Answered S3D on Reprap XXL screen Issues

    Printing straight from the LCD controller
    Post by: Sylva, Jun 23, 2017 in forum: Troubleshooting
  6. Sylva
    Thread

    Answered S3D on Reprap XXL screen Issues

    Hey All, SO after fixing other issues and getting good prints out of my printer while connected to my pc. I attached a RepRap XXL LCD screen top...
    Thread by: Sylva, Jun 23, 2017, 18 replies, in forum: Troubleshooting
  7. Sylva
    Post

    Solved E3D upgrade, M999 ERROR

    So it was a short in the wire and once replaced hasnt given me any issues but now Im having issues with simplify3d not working too great printing...
    Post by: Sylva, Jun 23, 2017 in forum: Troubleshooting
  8. Sylva
    Post

    Solved E3D upgrade, M999 ERROR

    Okay, how would I go about figuring out which of those possibilities is it?
    Post by: Sylva, Jun 4, 2017 in forum: Troubleshooting
  9. Sylva
    Thread

    Solved E3D upgrade, M999 ERROR

    Hey Guys, So I recently upgraded my robo+ to an e3d V6 and double checked the wiring and I am getting an M999 error code and simplify3D is saying...
    Thread by: Sylva, Jun 4, 2017, 6 replies, in forum: Troubleshooting
  10. Sylva
    Post

    Answered Alloy 910 Issues

    Cool, I'll start looking into it, thanks guys!
    Post by: Sylva, Dec 4, 2016 in forum: Troubleshooting
  11. Sylva
    Post

    Answered Alloy 910 Issues

    In MatterControl where do I find min. layer print time?
    Post by: Sylva, Dec 2, 2016 in forum: Troubleshooting
  12. Sylva
    Post

    Answered Alloy 910 Issues

    That is exactly the look!!
    Post by: Sylva, Dec 2, 2016 in forum: Troubleshooting
  13. Sylva
    Post

    Answered Alloy 910 Issues

    Ah okay, that makes sense now, you're running at 60mm-sec. so the only thing I can think of it being it environment causing it to cool too rapidly...
    Post by: Sylva, Dec 2, 2016 in forum: Troubleshooting
  14. Sylva
    Post

    Answered Alloy 910 Issues

    Sorry for the late reply been busy with the holidays. 3600mm/sec is insane. My printer is only at 60mm/s. maybe I haven't tuned my machine...
    Post by: Sylva, Dec 2, 2016 in forum: Troubleshooting
  15. Sylva
    Post

    Answered Alloy 910 Issues

    Not a problem! thankfully on this print it was support material that lifted but I'd like to nip it for my upcoming serious prints for my...
    Post by: Sylva, Nov 11, 2016 in forum: Troubleshooting
  16. Sylva
    Post

    Answered Alloy 910 Issues

    Currently printing a raptor claw from thingiverse and I have printed it the same direction with pla but for some odd reason lifts. thingiverse...
    Post by: Sylva, Nov 11, 2016 in forum: Troubleshooting
  17. Sylva
    Thread

    Answered Alloy 910 Issues

    Hey All, new to the forums officially although I lurk consistently. So I recently purchased Alloy 910 filament and have been having setting...
    Thread by: Sylva, Nov 11, 2016, 15 replies, in forum: Troubleshooting
Find older messages
Showing results 21 to 37 of 37
Search Again
Page 2 of 2