1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Jordan Serafin
    Post

    Unresolved Filament far from bed in areas, but closer in others

    I have repeatedly tightened them after times of maintenance. I have not done paper leveling, how would I go about doing this? From what I've...
    Post by: Jordan Serafin, Dec 1, 2016 in forum: Troubleshooting
  2. Jordan Serafin
    Thread

    Unresolved Filament far from bed in areas, but closer in others

    I have been dealing with this issue for a long time now, I am pretty well acquainted with my printer now (Robo3D R1+) after troubleshooting so...
    Thread by: Jordan Serafin, Dec 1, 2016, 4 replies, in forum: Troubleshooting
  3. Jordan Serafin
    Post

    Solved Hexagon extruder heatsink won't tighten

    Thanks for the response! It seems so far to not really affect my prints, but as soon as I see anything wrong happening, I'm just gonna buy a new one.
    Post by: Jordan Serafin, Oct 22, 2016 in forum: Troubleshooting
  4. Jordan Serafin
    Thread

    Solved Hexagon extruder heatsink won't tighten

    I bought new hexagon hotend kit and it worked fine until I kept smelling a burning smell. I noticed the heatsink probably wasn't tightened all the...
    Thread by: Jordan Serafin, Oct 19, 2016, 2 replies, in forum: Troubleshooting
  5. Jordan Serafin
    Post

    Solved Extruder heatsink badly clogged

    Got it unclogged! What do you mean by "season" the hotend?
    Post by: Jordan Serafin, Sep 5, 2016 in forum: Troubleshooting
  6. Jordan Serafin
    Post

    Solved Extruder heatsink badly clogged

    Thanks for the suggestions!
    Post by: Jordan Serafin, Sep 5, 2016 in forum: Troubleshooting
  7. Jordan Serafin
    Thread

    Solved Extruder heatsink badly clogged

    Hi, my printer had a clog after printing too close for too long. I tried unclogging it with guitar string, but was unable to since the clog went...
    Thread by: Jordan Serafin, Sep 5, 2016, 12 replies, in forum: Troubleshooting
  8. Jordan Serafin
    Post

    Solved Need help removing extruder

    Nevermind lol, I found the tutorial I was looking for! Xd
    Post by: Jordan Serafin, Sep 2, 2016 in forum: Troubleshooting
  9. Jordan Serafin
    Thread

    Solved Need help removing extruder

    Hi, my extruder is clogged, and I can't manage to use guitar string to push out the filament like I was previous times. I am trying to remove the...
    Thread by: Jordan Serafin, Sep 2, 2016, 5 replies, in forum: Troubleshooting
  10. Jordan Serafin
    Post

    Solved Bed Adhesion and Retraction Issues

    So as it turns out, I think the problem all along was the x-axis bars being-off level, with addition to the z-axis needing to be at the right...
    Post by: Jordan Serafin, Apr 10, 2016 in forum: Troubleshooting
  11. Jordan Serafin
    Post

    Solved Bed Adhesion and Retraction Issues

    Ok so I think I figured out after the fact that one area printed pretty perfectly, then when it moved to another part of the bed to print, it...
    Post by: Jordan Serafin, Apr 10, 2016 in forum: Troubleshooting
  12. Jordan Serafin
    Post

    Solved Print Head Moves up continuously when auto leveling

    Resolved, one of the z-axis switches (the one on the left side) was not making contact with the carriage, so I had to adjust it and all is well!
    Post by: Jordan Serafin, Apr 10, 2016 in forum: Troubleshooting
  13. Jordan Serafin
    Thread

    Solved Print Head Moves up continuously when auto leveling

    So for some reason, my printer head is now deciding to move up whenever it auto levels. As it moves to each corner where it would normally lower...
    Thread by: Jordan Serafin, Apr 9, 2016, 2 replies, in forum: Troubleshooting
  14. Jordan Serafin
    Post

    Solved Bed Adhesion and Retraction Issues

    I don't know what to try anymore, I have fiddled with different gcode, each of which include auto-levelling and height adjustment, I have tried...
    Post by: Jordan Serafin, Apr 9, 2016 in forum: Troubleshooting
  15. Jordan Serafin
    Post

    Solved Bed Adhesion and Retraction Issues

    Any suggestions on the retraction issue?
    Post by: Jordan Serafin, Apr 6, 2016 in forum: Troubleshooting
  16. Jordan Serafin
    Post

    Solved Bed Adhesion and Retraction Issues

    Unfortunately I thought I had the number down lol, but still some minor issues, so I'm still fine tuning....but no I haven't tried fiddling with...
    Post by: Jordan Serafin, Apr 5, 2016 in forum: Troubleshooting
  17. Jordan Serafin
    Post

    Solved Bed Adhesion and Retraction Issues

    Ok, I may have found the magic number now :) yay! An offset of .87 seems to be working so far, I may try with .88 to see which is better.
    Post by: Jordan Serafin, Apr 4, 2016 in forum: Troubleshooting
  18. Jordan Serafin
    Post

    Solved Bed Adhesion and Retraction Issues

    Yup, the z offset is my issue, I just printed with mattercontrol with no issue, now I am trying to get cura to realize that I am changing the z...
    Post by: Jordan Serafin, Apr 3, 2016 in forum: Troubleshooting
  19. Jordan Serafin
    Post

    Solved Bed Adhesion and Retraction Issues

    Nothing there really helped, and I still haven't been able to resolve the issue. I am trying to edit the g code where it says "M565 Z-1 ;" and I...
    Post by: Jordan Serafin, Apr 3, 2016 in forum: Troubleshooting
  20. Jordan Serafin
    Post

    Solved Bed Adhesion and Retraction Issues

    Ok thanks! I'll check that out
    Post by: Jordan Serafin, Apr 3, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 21 Next >
Search Again
Page 1 of 2