1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Dan Ershen
    Post

    Solved Extruder Stepper Motor Twitch

    Apparently the heat sink for my extruder stepper driver fell off, causing the chip to fry. Replaced the stepper driver, and the issue is solved!
    Post by: Dan Ershen, Jan 21, 2017 in forum: Troubleshooting
  2. Dan Ershen
    Post

    Solved Extruder Stepper Motor Twitch

    Wiring is confirmed correct. Mirrors the other stepper motor wires. How would I go about fixing the stepper motor driver? And is the driver on...
    Post by: Dan Ershen, Jan 18, 2017 in forum: Troubleshooting
  3. Dan Ershen
    Post

    Solved Extruder Stepper Motor Twitch

    Not 100 percent certain I got the wires correctly. The wire pin alignment I set is shown in the video above. I just tried connecting the wire to...
    Post by: Dan Ershen, Jan 18, 2017 in forum: Troubleshooting
  4. Dan Ershen
    Thread

    Solved Extruder Stepper Motor Twitch

    Hey all, Recently the pin in the JST connector leading to the stepper motor for the extruder fell out, so I ordered a replacement cable. After...
    Thread by: Dan Ershen, Jan 18, 2017, 11 replies, in forum: Troubleshooting
  5. Dan Ershen
    Post

    Partially Solved Autolevel going through the bed

    Ended up sorta solving it by going to the machine settings in Simplify3d and raising the z in that. Still having issues with the extruder being...
    Post by: Dan Ershen, Dec 8, 2016 in forum: Troubleshooting
  6. Dan Ershen
    Thread

    Partially Solved Autolevel going through the bed

    I cracked my bed, and ended up replacing it with glass that is thicker than the original bed. Now, when my printer attempts to do the autolevel...
    Thread by: Dan Ershen, Dec 6, 2016, 5 replies, in forum: Troubleshooting
  7. Dan Ershen
    Post

    Unresolved Printer stops extruding mid print

    Tried with PLA, PLA+, PLA Wood, ABS, and T-Glase. No joy. And no, it's any model I make, not just one STL file.
    Post by: Dan Ershen, Jul 22, 2016 in forum: Troubleshooting
  8. Dan Ershen
    Thread

    Unresolved Printer stops extruding mid print

    Hey guys, I've had my Robo3d r1+ for a bit now, and I've run into an issue I can't figure out. For some reason, halfway through the print in...
    Thread by: Dan Ershen, Jul 22, 2016, 4 replies, in forum: Troubleshooting
  9. Dan Ershen
    Post

    Solved Printer aborts print 15 minutes, motors sound like jammed

    I'm more amazed you were able to know the issue from that little info.
    Post by: Dan Ershen, Mar 24, 2016 in forum: Troubleshooting
  10. Dan Ershen
    Post

    Solved Printer aborts print 15 minutes, motors sound like jammed

    DING DING DING! Winner! The fan was running, but the board was still overheating I think. I rigged a second externally powered fan to cool the...
    Post by: Dan Ershen, Mar 24, 2016 in forum: Troubleshooting
  11. Dan Ershen
    Post

    Solved Printer aborts print 15 minutes, motors sound like jammed

    Running another print now. Will try and pull the USB right as it fails to capture the original error
    Post by: Dan Ershen, Mar 16, 2016 in forum: Troubleshooting
  12. Dan Ershen
    Post

    Solved Printer aborts print 15 minutes, motors sound like jammed

    It won't let me scroll any further than that Sent from my iPhone using Tapatalk
    Post by: Dan Ershen, Mar 16, 2016 in forum: Troubleshooting
  13. Dan Ershen
    Thread

    Solved Printer aborts print 15 minutes, motors sound like jammed

    Hi all, So lately I can't get my R1+ with an e3d volcano to print. It will print the skirt and first 5 layers fine, then the printer will make a...
    Thread by: Dan Ershen, Mar 15, 2016, 8 replies, in forum: Troubleshooting
Showing results 1 to 13 of 13
Search Again