1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    This is all yours guys ! thanks a lot for everything ! the time, the patience !! everything! Just thanks! after a few small parts now im printing...
    Post by: Marcos Zuccaro, Jun 25, 2017 in forum: Troubleshooting
  2. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    Tried a lot in differents positions and tightenings, same error message. The first picture its a really bad one but i can tell that both...
    Post by: Marcos Zuccaro, Jun 24, 2017 in forum: Troubleshooting
  3. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    When i start up i get the message of maxtemp. Then MC says its 0º / 0º and if i move the thermistor cable a little bit the temperature reading...
    Post by: Marcos Zuccaro, Jun 23, 2017 in forum: Troubleshooting
  4. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    i done it , but now i have the message : "Error reported : Extruder switched off. MAXTEMP triggered!" when i start it ... every connection its...
    Post by: Marcos Zuccaro, Jun 23, 2017 in forum: Troubleshooting
  5. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    firs problem as soon as trying to put it in ... i tried to set the latch back into position but its looks like the hot end its too big to let the...
    Post by: Marcos Zuccaro, Jun 23, 2017 in forum: Troubleshooting
  6. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    Great bro im assemblying it and give it a try... brb ! thx again ! the beer i owe you just turned into a whiskey ! ^^
    Post by: Marcos Zuccaro, Jun 23, 2017 in forum: Troubleshooting
  7. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    oh okey, i was worried about that gap... i couldnt make it even... the rest looks great... i dont know if i have to tighten it up a little bit...
    Post by: Marcos Zuccaro, Jun 23, 2017 in forum: Troubleshooting
  8. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    Hey guys ! MR annoying here again !...Hmmm i manage to put everything back together but even hot i cant finish tightening the nozzle. here is a...
    Post by: Marcos Zuccaro, Jun 23, 2017 in forum: Troubleshooting
  9. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    I forgot i had an allen like tool that came with the R1+ that fits perfectly trough the hole. It worked like wonders ! im gonna let it cool and...
    Post by: Marcos Zuccaro, Jun 22, 2017 in forum: Troubleshooting
  10. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    Thanks for your replies guys ! Im in Argentina ^^ far south of the continent haha. I managed to remove both , thermistor and heater should i...
    Post by: Marcos Zuccaro, Jun 22, 2017 in forum: Troubleshooting
  11. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    So i did the disassembly of the hotend... i removed the nozzle and it looks unobstructed. I have some doubts about the heatbreak/heatblock part......
    Post by: Marcos Zuccaro, Jun 21, 2017 in forum: Troubleshooting
  12. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    You have surpassed the limits of awesomeness! Thank you! I will update if everything worked and close it!
    Post by: Marcos Zuccaro, Jun 21, 2017 in forum: Troubleshooting
  13. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    okey then... dissasembling everything it is ! hahaha. I dont have the luxury of a mistake since i cant get good replacement where im from :( . So...
    Post by: Marcos Zuccaro, Jun 21, 2017 in forum: Troubleshooting
  14. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    Great ! I got a response from Robo3d that says : " Hi Marcos Try heating and then pushing through with something good and stiff that is close to...
    Post by: Marcos Zuccaro, Jun 21, 2017 in forum: Troubleshooting
  15. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    can i disassemble the heatsink from the heatbreak without removing the nozzle? or the procedure is nozzle then the heatsink. All of this allways...
    Post by: Marcos Zuccaro, Jun 21, 2017 in forum: Troubleshooting
  16. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    Great thx for the help Mark, i will thread a little more the heater block. This doesnt happen very often, in more than a year this is the second...
    Post by: Marcos Zuccaro, Jun 19, 2017 in forum: Troubleshooting
  17. Marcos Zuccaro
    Thread

    Solved JAM, filament stuck past heatsink

    So i have this problem, i had it before but now i cant get it out. I send a print and for some reason it started printing too close to the bed. I...
    Thread by: Marcos Zuccaro, Jun 19, 2017, 35 replies, in forum: Troubleshooting
  18. Marcos Zuccaro
    Post

    Partially Solved Weird sounds

    Thanks man! That was a really quick answer! I will replace the fan and check out if thats the problem. I saw a couple of mods that change the...
    Post by: Marcos Zuccaro, Apr 8, 2017 in forum: Troubleshooting
  19. Marcos Zuccaro
    Thread

    Partially Solved Weird sounds

    [MEDIA] I have a robo 3d r1+ with a year old. It started making an static sound like shown in the vid. Plus the weird sound that sounds like a...
    Thread by: Marcos Zuccaro, Apr 8, 2017, 4 replies, in forum: Troubleshooting
  20. Marcos Zuccaro
    Post

    Solved Hot end without screws Jammed!

    I had a meeting via skype with the tech support of robo 3d and they helped me out in seven minutes i was re-assembling my 3d printer and i was...
    Post by: Marcos Zuccaro, Mar 19, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 24 Next >
Search Again
Page 1 of 2