1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. erer1243
    Post

    Solved Thermal Runaway, never seen this problem before. (R1 Plus)

    Got it working by doing some PID tuning. Mysterious that it just appeared as a problem, but it's fixed now.
    Post by: erer1243, Mar 26, 2017 in forum: Troubleshooting
  2. erer1243
    Post

    Solved Thermal Runaway, never seen this problem before. (R1 Plus)

    If there's no actual problem then I probably won't spend any money. It seems to just be a pid setting issue. Don't know why it happened but after...
    Post by: erer1243, Mar 26, 2017 in forum: Troubleshooting
  3. erer1243
    Post

    Solved Thermal Runaway, never seen this problem before. (R1 Plus)

    I think I might've just found the problem. When the fans switch from 100% (what they always start the print at) to 255% speed, the temperature...
    Post by: erer1243, Mar 26, 2017 in forum: Troubleshooting
  4. erer1243
    Post

    Solved Thermal Runaway, never seen this problem before. (R1 Plus)

    I don't think the problem is wiring. When the wire is disconnected, it immediately pushes a mintemp error and halts, not thermal runaway. If the...
    Post by: erer1243, Mar 26, 2017 in forum: Troubleshooting
  5. erer1243
    Post

    Solved Thermal Runaway, never seen this problem before. (R1 Plus)

    Alright I will try that.
    Post by: erer1243, Mar 26, 2017 in forum: Troubleshooting
  6. erer1243
    Post

    Solved Thermal Runaway, never seen this problem before. (R1 Plus)

    I just cleaned the head and reseated all the connectors that ride around on the carriage. I don't know exactly how to test this without just...
    Post by: erer1243, Mar 26, 2017 in forum: Troubleshooting
  7. erer1243
    Post

    Solved Thermal Runaway, never seen this problem before. (R1 Plus)

    The thermistor is in place and the wires look good. I don't know what you mean by flaky.
    Post by: erer1243, Mar 26, 2017 in forum: Troubleshooting
  8. erer1243
    Thread

    Solved Thermal Runaway, never seen this problem before. (R1 Plus)

    Hi, fun to be back on the forums, though unfortunately with a problem. Starting yesterday, on all my prints, at about 5 to 10 minutes in there is...
    Thread by: erer1243, Mar 26, 2017, 12 replies, in forum: Troubleshooting
  9. erer1243
    Post

    Is this unspooled filament done for?

    Well, regarding the thinking it's okay to put it in tangled... I have done that and yes, it has untangled itself. I've done this twice now and...
    Post by: erer1243, Aug 30, 2016 in forum: General Questions
  10. erer1243
    Thread

    Is this unspooled filament done for?

    Long story short, couple little kids got a hold of a spool of filament I have. Here's what it looks like. I can't pull it end to end as it's...
    Thread by: erer1243, Aug 29, 2016, 8 replies, in forum: General Questions
  11. erer1243
    Post

    Answered How do you guys stop filament from tangling on the spool?

    Thanks for the replies. I will try some of the clips or maybe the paperclip trick. Hopefully it will help.
    Post by: erer1243, Aug 8, 2016 in forum: Troubleshooting
  12. erer1243
    Thread

    Answered How do you guys stop filament from tangling on the spool?

    I have only used hatchbox PLA, just to preface. It seems every time I print something, I need to stand by to help the filament not get stuck on...
    Thread by: erer1243, Aug 6, 2016, 6 replies, in forum: Troubleshooting
  13. erer1243
    Post

    Solved Z axis doesn't seem to work evenly.

    I have one. Now that I switched to octopi however, many of the controls don't work, including the speed regulator. I do use it as a temp/progress...
    Post by: erer1243, Aug 5, 2016 in forum: Troubleshooting
  14. erer1243
    Post

    Solved Z axis doesn't seem to work evenly.

    I will probably just install a dual fan mount. I have an electronics store 10 mins from here that sells those fans for $1 a piece. I will just buy...
    Post by: erer1243, Aug 4, 2016 in forum: Troubleshooting
  15. erer1243
    Post

    Solved Z axis doesn't seem to work evenly.

    I use a 15 sec minimum layer time just for no possible problems, 5-10 once or twice ive done when the part is extra tiny. I will lower the hotend...
    Post by: erer1243, Aug 4, 2016 in forum: Troubleshooting
  16. erer1243
    Post

    Solved Z axis doesn't seem to work evenly.

    I found a new problem. One that may explain previous problems with crashing and mushing. I still have a suspicion that the z axis goes up unevenly...
    Post by: erer1243, Aug 4, 2016 in forum: Troubleshooting
  17. erer1243
    Post

    Solved Z axis doesn't seem to work evenly.

    I see that in the video from danzca6. I have used steppers and drivers plenty though none of my drivers have such a physical voltage controller. I...
    Post by: erer1243, Aug 4, 2016 in forum: Troubleshooting
  18. erer1243
    Post

    Solved Z axis doesn't seem to work evenly.

    Sorry, misread the comment. However, isn't what I said even more true now? How do you tune a circuit board? What is there to tune? There is no...
    Post by: erer1243, Aug 4, 2016 in forum: Troubleshooting
  19. erer1243
    Post

    Solved Z axis doesn't seem to work evenly.

    Reply to all 3 comments up till now: What exactly do you mean by tuned? It's a stepper, it always performs the same, no? Also, relative to the...
    Post by: erer1243, Aug 4, 2016 in forum: Troubleshooting
  20. erer1243
    Post

    Solved Z axis doesn't seem to work evenly.

    Sorry, totally neglected that. I have an r1 +plus. No modifications or major tuning whatsoever and only about 2 months old.
    Post by: erer1243, Aug 4, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 35 Next >
Search Again
Page 1 of 2