1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Dennis Pyles
    Post

    Where to get firmware for new board

    Didnt mean to everything in bold. Copied and pasted description and then the font size and bold stuck. Thanks for the link. If I understand you...
    Post by: Dennis Pyles, Jan 15, 2017 in forum: Mods and Upgrades
  2. Dennis Pyles
    Thread

    Where to get firmware for new board

    I purchased the OSOYOO 3D Printer Kit with RAMPS 1.4 Controller + Mega 2560 board + 5pcs A4988 Stepper Motor Driver with Heatsink + LCD 12864...
    Thread by: Dennis Pyles, Jan 15, 2017, 3 replies, in forum: Mods and Upgrades
  3. Dennis Pyles
    Thread

    Unanswered Hex fan question

    I have an R1+. I started having a problem with extrusion stopping after about 5 to 7 minutes. I thought it might have been a thermistor issue,...
    Thread by: Dennis Pyles, Dec 12, 2016, 2 replies, in forum: Troubleshooting
  4. Dennis Pyles
    Post

    Solved Stud Thermistor for R1+

    Do I need to call to get them? I didnt see any thermistors at the store at all
    Post by: Dennis Pyles, Dec 12, 2016 in forum: Troubleshooting
  5. Dennis Pyles
    Post

    Solved Stud Thermistor for R1+

    I've emailed but no response yet. Maybe I should call. But I need them quickly
    Post by: Dennis Pyles, Dec 12, 2016 in forum: Troubleshooting
  6. Dennis Pyles
    Thread

    Solved Stud Thermistor for R1+

    I have the R1+ and I need a new stud thermistor. The store on here has none at all. The ones I see on printedsolid are all screw in thermistor....
    Thread by: Dennis Pyles, Dec 12, 2016, 6 replies, in forum: Troubleshooting
  7. Dennis Pyles
    Post

    Solved Bad extruder stepper motor or bad board?

    Thats helps tremendously. One other question, what about the firmware? I have a ROBO 3D R1+
    Post by: Dennis Pyles, Dec 6, 2016 in forum: Troubleshooting
  8. Dennis Pyles
    Post

    Solved Bad extruder stepper motor or bad board?

    I just got my RAMPS kit OSOYOO 3D Printer Kit with RAMPS 1.4 Controller + Mega 2560 board + 5pcs A4988 Stepper Motor Driver with Heatsink + LCD...
    Post by: Dennis Pyles, Dec 6, 2016 in forum: Troubleshooting
  9. Dennis Pyles
    Post

    Solved Bad extruder stepper motor or bad board?

    I will be ordering the kit. Until then I am going to try to "tune" the card to keep me going til then. Do you know where I can find a diagram to...
    Post by: Dennis Pyles, Dec 4, 2016 in forum: Troubleshooting
  10. Dennis Pyles
    Post

    Solved Bad extruder stepper motor or bad board?

    Refresh my memory please. I bought this May 24th 2016. It's only got a 6 month warranty though doesnt it?
    Post by: Dennis Pyles, Dec 4, 2016 in forum: Troubleshooting
  11. Dennis Pyles
    Thread

    Solved Bad extruder stepper motor or bad board?

    I was changing the filament on my R1+ and when I tried to extrude the filament via matter control I ended up getting a stuttering "machine gun...
    Thread by: Dennis Pyles, Dec 4, 2016, 11 replies, in forum: Troubleshooting
  12. Dennis Pyles
    Thread

    Unanswered Z Axis off

    When I try to home the printer (Robo 3D R1plus) it seems to be pushing down on the plate and in matter control is says the co-ordinates are...
    Thread by: Dennis Pyles, Jul 8, 2016, 0 replies, in forum: Troubleshooting
Showing results 1 to 12 of 12
Search Again